Burley 4111-R Installation, Servicing  & User Instructions Download Page 18

 

17 

Glass 

Outlet Grille 

Combustion 
Air inlets 

If  you  have  any  questions  or  the  appliance  is  not  operating  correctly,  phone  the  Burley  help-line 
BEFORE you leave the installation. 

 

If  the  appliance  is  not  fitted  in  strict  accordance  with  these  instructions,  Burley  cannot  be  held 
responsible for any damage caused and reserve the right to charge for any corrective work. 

 

Note:  When  lighting  the  fire  from  very  cold,  it  may  sometimes  switch  itself  off  after  about  1  min. 
This is the very sensitive oxygen depletion circuit proving itself and is normal. Wait for 1 minute and 
relight fire. To avoid this happening it is possible to leave the pilot alight at all times. 

 

11.0 Fireguards

 

 

A fireguard is not supplied with this appliance; however it is recommended that a fireguard to BS6539 
or BS6778 is fitted if the fire is to be used in the presence of young children, the elderly and the infirm. 
The  glass  screen  acts  as  a  fireguard  and  also  directs  the  combustions  products  through  the  safety 
catalyst. The appliance must not be operated with the glass removed.

 

 

12.0 

Instruct the User 

It is important to hand these instructions to the user for safe keeping and future reference. 

The user shall be instructed how to fully operate the appliance, remotely and manually and shown how 
to adjust the thermostat for desired comfort levels. 

The user shall also be made aware of the precautions to prevent blockage of any purpose made room 
ventilation, and the need to keep soft furnishings away from the appliance. 

The  outlet  grille  and  glass  on  the  appliance  are  working  surfaces.  On  no  account  should  these  be 
covered or obstructed. The air inlets should also be kept clear. 

The user shall be made aware of the need to operate the appliance safely in accordance with sections 
8-12 of the instructions and of the need for regular servicing and maintenance (section 13). 

The user shall be informed of the need for at least an annual service and the importance of returning 
the guarantee card. 

The installer section of the guarantee card must be filled in fully to validate the 

warranty.

 

Advise  that  a  fireguard  to  BS6539  or  BS6778  should  be  used  for  the  protection  of  the  elderly,  the 
infirm or children. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for 4111-R





























Reviews: