24
Adjust soluble tank temperature
(190° F maximum)
Adjust minimum soluble tank ready tem-
perature for lockout (185° maximum)
Takes you to the SET BEVERAGE
SIZE sub-menu to adjust beverage
size.
TANK TEMP XXX°
(-)
EXIT
(+)
READY TEMP XXX°
(-)
EXIT
(+)
SET BEVERAGE SZ
EXIT YES
ESPRSO TEMP XXX°
(-) EXIT
(+)
Set espresso tank temperature.
DIAGNOSTICS
EXIT YES
Takes you to the DIAGNOSTICS menu
to test components.
FACTORY DEFAULTS
NO
YES
LEFT HOPPER STR
(-)
##
(+)
TEST LEFT HOPPER
PRESS DISPENSE
AUGER DELAY
(-) .50 sec (+)
Takes you to the FACTORY DEFAULTS
sub-menu to enable restoring factory
defaults.
Use +/- buttons to increase or decrease
powder hopper speed. This menu
repeats for middle and right hopper.
Pressing any dispense button will run
hopper for 10 seconds, at speed set in the
menu above. This allows a catch test.
Delays the start of the hopper mo-
tors after dispense valve opens. This
prevents soluble powder from entering
mixing chamber ahead of hot water.
WHIPPER DELAY
(-) .00 sec (+)
CAL HOT WATER
PRESS DISPENSE
This delays the start of the whipper
motors after the dispense valve opens.
Pressing any dispense button opens
the hot water valve for ten seconds.
This allows the valve to be adjusted for
the proper flow rate.
Pressing any dispense button opens
the left hot water valve for ten
seconds. This allows the valve to be
adjusted for the proper flow rate.
PUMP START DELAY
(-)
.# sec
(+)
ESP THRESHOLD
(-)
###
(+)
PSTN HOME THRESOLD
(-)
###
(+)
CAL BEAN HOPPER
EXIT YES
This delays the start of the espresso
pump after the espresso valve opens.
This sets the current level at which
the piston sees, to signal the motor to
shut down in the wipe position.
This sets the current level at which
the piston sees, to signal the motor to
shut down in the home position.
This calibrates the photo sensor on
the bean hopper by detecting the am-
bient light with the hopper empty, then
setting a threshold for signaling when
the hopper is empty.
CAL LFT PWDR VLV
PRESS DISPENSE
GLOSSARY
PRE-HEAT ESP GRP
NO
EXIT YES
This asks if you want to enable
pre-heating of the espresso group, if
espresso has not been brewed within
“X” amount of time. For espresso
shots only - not for specialty drinks.
ESPRSO READY XXX°
(-)
EXIT
(+)
Set espresso tank ready temperature.
Tank temp. must reach this to enable
brewing if brew lockout is set.
STRENGTH ADJUST
EXIT YES
Takes you to the STRENGTH ADJUST
sub-menu to adjust soluble hopper
speeds and grinder times.
CALIBRATION
EXIT YES
Takes you to the CALIBRATION
sub-menu.
Takes you to the SET ESPRESSO
SHOTS sub-menu to set up espresso
shots.
SET ESPRSO SHOTS
EXIT YES
Takes you to the LOCK/DISABLES
sub-menu.
LOCKS/DISABLES
EXIT YES
SM ESP GRIND TIME
(-) #.# sec
(+)
Pressing any dispense button will run
grinder for the small espresso pro-
grammed time. This allows a catch test.
Menu repeats for large espress grind time.
TEST SM GRIND
DISPENSE TO TEST
Pressing any dispense button will run
grinder for the small espresso programmed
time. This allows a catch test. Menu
repeats for large espresso grind time.
SELECT UNITS
ENG EXIT METRIC
Allows applicable data to be displayed in
English or Metric units.
0 REFILL 155
(-)
EXIT
(+)
Sets threshold for refill probe on soluble
water tank. Allows adjustment for different
water conditions.
Pressing any dispense button opens
the right hot water valve for ten
seconds. This allows the valve to be
adjusted for the proper flow rate.
CAL RT PWDR VLV
PRESS DISPENSE
SET PRE-HEAT TIME
(-) ###min (+)
Sets the amount of time (in minutes),
that if exceeded, will automatically go
into pre-heat routine, if an espresso
shot is selected to be dispensed.
52384.0 101116
ESPR TANK: ###F
Live temperature display, or probe
fault codes.
PWDR TANK: ###F
