Bunn IMIX-3S+ Installation & Operating Manual Download Page 31

Page: 31 / 33

PROGRAMMING MENU’S (cont.)

52384.0 101116

WILL REPLACE ALL

DISPENSE SETUPS

“H”

ARE YOU SURE

NO YES

EXIT TO HOME

SCREEN

RETURN TO (N)

Build A Beverage - Standard Menu

SETUP SW 1 RECIPE

NO YES

NOTE: Press and release right switch to advance to next menu.

RECIPE SETUP?

USER SELECT MODE

SINGLE MULTI

SWITCH 1 RECIPE

EXIT YES

(-) CAPPUCCINO (+)

SW 1 SMALL TM

(-) ##.# (+)

SW 1 LARGE TM

Standard Menu

DO THIS FOR ALL 10 SWITCHES

Select Single Touch or Multi

Touch

Multi touch screens on the

left, their replacements for

single touch on right.

If No, move to next recipe.

If Yes, move into current

recipe. Switch 1’s associated

LED turns ON.

Any preset recipe is select-

able, or they can also select

“DISABLE” to turn off key.

and can select CUSTOM to

build their own.

The TIME screen will not

show up if the recipe is dis-

abled, but for Espresso, Shot

size must still be picked.

Will not show up if the recipe

selected is Espresso or Dis-

abled.

Goes back to “SETUP SW 1

RECIPE? for the next switch

in the sequence..

SW DRINK SIZE

SMALL LARGE

SW 1 DISPNSE TM

(-) ##.# (+)

Summary of Contents for IMIX-3S+


































Search results

Summary of Contents for IMIX-3S+

Reviews:

Related manuals for IMIX-3S+

Brands by name

Popular brands

Bunn IMIX-3S+, Installation & Operating Manual

Search results

Summary of Contents for IMIX-3S+

Reviews:

Related manuals for IMIX-3S+

Brands by name

Popular brands