Bull NovaScale Blade 2040 Series Installation And User Manual Download Page 45

Page: 45 / 104

Installing options

Remove the air baffle and set aside for reinstallation.

Prepare for microprocessor installation.

CAUTION:

Processors must be installed in order, starting with processor 1 and proceeding with
processor 2, 3, and 4, based on whether the system has a single, dual or quad processor
configuration. A three-processor configuration is NOT supported.

Locate the appropriate microprocessor socket(s) on the system board for installing an additional
microprocessor (see the following figure).

Table 3. Microprocessor installation order

Configuration

Socket(s) used

Single microprocessor configuration

CPU1

Dual microprocessor configuration

CPU1, CPU2

Quad microprocessor configuration

CPU1, CPU2, CPU3, CPU4

TP00434

Summary of Contents for NovaScale Blade 2040 Series









































































































Search results

Summary of Contents for NovaScale Blade 2040 Series

Reviews:

Bull NovaScale Blade 2040 Series, Installation And User Manual, Page: 45 / 104

Search results

Summary of Contents for NovaScale Blade 2040 Series

Reviews: