Bryston SP3 Manual Download Page 70

Page: 70 / 72

SP3 IDLE SCREEN EXPLANATIONS

Page 2 of 3

2. Default screen, playing HDMI input, Dolby Digital encoded multi-channel stream,

example 2

Line1: SRC: DVD HDMI1

Line2: IN: Dd Digital 48k 5.1

Line3: OUT: PL2xMovie7 EX

7.1

Line4: VOLUME: -30.0dB

Playing multichannel (5.1) source from DVD disk, through HDMI. Listening setup consists of 8

speakers (2 front, 2 surround, 2 back and 1 subwoofer).

Indicates Dolby Pro Logic EX algorithm for back channels re-creation. Capital “EX” lettering indicates

that the back channel re-creation is being forced upon any 5.1 channel source even in the absence of the

Dolby back channel enabling flag (YBSE – “Yes Back Surr Encoded”). This forcing feature is governed

by SOURCE SETUP



DOLBY



EX APPLY=FORCE . Note: EX APPLY=AUTO would reproduce

back speakers only when YBSE flag is present in the source stream., in such a cese lower case “ex” would

show.

Source

Input type (HDMI input socket #1)

Program encoding

Dolby Digital

Sample rate (kHz)

Program format (numspeakers.lfe)

Back channel re-creation mode: 5.1



7.1 “Movie7” (Dolby only)

Listening format (numspeakers.subwoof)

Output volume control (level in dB)

Dolby Pro Logic EX is on (back speakers)

APPENDIX M: SP3 IDLE SCREEN EXPLANATIONS continued

Summary of Contents for SP3









































































Search results

Summary of Contents for SP3

Reviews:

Brands by name

Popular brands

Bryston SP3, Manual

Search results

Summary of Contents for SP3

Reviews:

Brands by name

Popular brands