Bryston SP3 Manual Download Page 16

Page: 16 / 72

1x USB 2.0 type B

OUTPUTS

Analog Outputs:

10 balanced XLR male:

Left, Centre, Right, Left Surround, Right Surround, Left Back, Right Back, Left Auxiliary, Right Auxil-

iary and Subwoofer

16 sindle ended (unbalanced) RCA:

Left, Centre, Right, Left Surround, Right Surround, Left Back, Right Back, Left Auxiliary, Right Auxil-

iary & Subwoofer, 4 tape outputs, 2 Zone Two outputs.

Digital Outputs:

2x HDMI

1x TOSLINK optical

Trigger Inputs/Outputs:

One 12V input and 3 programmable trigger outputs

DATA & CONTROL PORTS:

1x Infra-Red sensor; remote control receiver

1x mini (3mm) phone jack (2 conductor) for auxilliary infra-red control data input

1x Ethernet (RJ45 connector): bilateral data, software download, etc.

INFRA-RED REMOTE CONTROL

Number of buttons:

Power Source:

two AAA batteries

IR Wavelength:

940nm

PHYSICAL SPECIFICATIONS

Dimensions:

17”W x 14.25”D (not including knobs & connectors) x 5.75”H (not including rubber feet)

17”W x 15.38”D (including knobs & connectors) x 6.25”H (including rubber feet)

Also available with 19”W dress panels (all other dimensions are the same)

Weight:

approx 22 lbs (10 kg)

Chassis Temp:

50 deg Celsius max.

Specifications subject to change without notice.

TRADEMARK ACKNOWLEDGEMENTS

Summary of Contents for SP3









































































Search results

Summary of Contents for SP3

Reviews:

Brands by name

Popular brands

Bryston SP3, Manual

Search results

Summary of Contents for SP3

Reviews:

Brands by name

Popular brands