manualshive.com logo in svg

Bryston SP3, Manual

Share
Download
Bryston SP3 Manual Download Page 51

SP3 Dolby Volume/DRC Screen 

Page 3 of 3

recording (as it should have been listened to originally, in a studio etc).  For 

example, when listening to a movie, this value could be increased

5

initially during 

the loudest portion of the recording,  to set the reference for the loudest parts.  A 

positive VOL OFFS value makes the average output sound less loud, negative 

value makes it louder.  

Note: Dd VOL OFFS does NOT have to be continously 

adjusted during a playback; this is an optional once-off 

(per movie) adjustment!

Line 4:  Dd VOL MID/SIDE OFF – use volume knob or SURROUND left/right arrow to 

toggle this parameter ON or OFF.   MID/SIDE is relevant only in STEREO mode 

and causes Dolby Volume algorithm to automatically re-balance the left and right 

channels. Default is OFF.

Note: Dolby Volume algorithm is operating only at lower 

sample rates <=48kHz.  It is automatically disabled above 

48kHz but this is not indicated on screen!  

No configuration settings are available for DRC selections.

5

+6dB is often sufficient to adjust the loudest movie scenes down to a comfortable level.

APPENDIX 

I

:  DOLBY VOLUME/DRC SET  continued

Summary of Contents for SP3









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands