Bryston SP3 Manual Download

Page: 34 / 72

APPENDIX F

WEB INTERFACE GUIDE

SP3 Web Interface Guide

Page 1 of 7

SP3 Web Interface Guide

2012-08-02, Stan Bleszynski, Bryston Ltd.

1. General guidelines (introduction).

SP3 can be connected to a PC (Windows, MacOS, Linux etc) using Ethernet cable through a local area network

hub or through a direct peer-to-peer (SP3-to-PC) using a cross-over network cable. Connection between SP3

and a PC can be established using either one of the 3 basic configuration schemes differing in the way the IP

addresses are leased out or assigned by an external or internal DHCP server. This is described in more details

in the following document on-line:

ftp://ftp.bryston.com/pub/firmware/sp3/doc/SP3_setup_using_LAN2.doc

Main SP3 web interface screen

2. Main screen.

Communication interface with the SP3 takes place over TCP/IP stack using HTTP (version 2 compat) protocol

over port 80. This can be handled by almost any internet browser, for example Internet Explorer, Chrome,

Safari, Firefox, Opera, and on any operating system platform. Once a connection is established, so-called “Net

Summary of Contents for SP3









































































Search results

Summary of Contents for SP3

Reviews:

Related manuals for SP3

Brands by name

Popular brands

Bryston SP3, Manual

Search results

Summary of Contents for SP3

Reviews:

Related manuals for SP3

Brands by name

Popular brands