Bryant 582J 04 Series Installation Instructions Manual Download Page 43

Page: 43 / 44

UNIT START-UP CHECKLIST

(Remove and Store in Job File)

NOTE: To avoid injury to personnel and damage to equipment or property when

completing the procedures listed in this start---up checklist, use good judgement,

follow safe practices, and adhere to the safety considerations/information as

outlined in the preceding sections of this Installation Instructions document.

MODEL NO.:

SERIAL NO.:

I. PRE-START-UP

VERIFY THAT ALL PACKAGING MATERIALS HAVE BEEN REMOVED FROM UNIT

VERIFY INSTALLATION OF OUTDOOR AIR HOOD

VERIFY INSTALLATION OF FLUE EXHAUST AND INLET HOOD

VERIFY THAT CONDENSATE CONNECTION IS INSTALLED PER INSTRUCTIONS

VERIFY THAT ALL ELECTRICAL CONNECTIONS AND TERMINALS ARE TIGHT

VERIFY GAS PRESSURE TO UNIT GAS VALVE IS WITHIN SPECIFIED RANGE

CHECK GAS PIPING FOR LEAKS

CHECK THAT INDOOR--AIR FILTERS ARE CLEAN AND IN PLACE

CHECK THAT OUTDOOR AIR INLET SCREENS ARE IN PLACE

VERIFY THAT UNIT IS LEVEL

CHECK FAN WHEELS AND PROPELLER FOR LOCATION IN HOUSING/ORIFICE AND VERIFY

SETSCREW IS TIGHT

VERIFY THAT FAN SHEAVES ARE ALIGNED AND BELTS ARE PROPERLY TENSIONED

VERIFY THAT SCROLL COMPRESSORS ARE ROTATING IN THE CORRECT DIRECTION

VERIFY INSTALLATION OF THERMOSTAT

VERIFY THAT CRANKCASE HEATERS HAVE BENN ENERGIZED FOR AT LEAST 24 HOURS

II. START-UP

ELECTRICAL

SUPPLY VOLTAGE

L1--L2

L2--L3

L3--L1

COMPRESSOR AMPS 1

COMPRESSOR AMPS 2

SUPPLY FAN AMPS

TEMPERATURES

OUTDOOR--AIR TEMPERATURE

F DB (DRY BULB)

RETURN--AIR TEMPERATURE

F DB

F WB (WET BULB)

COOLING SUPPLY AIR TEMPERATURE

GAS HEAT SUPPLY AIR

PRESSURES

GAS INLET PRESSURE

IN. WG

GAS MANIFOLD PRESSURE STAGE 1

IN. WG

STAGE 2

IN. WG

REFRIGERANT SUCTION

CIRCUIT A

PSIG

CIRCUIT B

PSIG

REFRIGERANT DISCHARGE CIRCUIT A

PSIG

CIRCUIT B

PSIG

VERIFY REFRIGERANT CHARGE USING CHARGING CHARTS

582J

Summary of Contents for 582J 04 Series













































Search results

Summary of Contents for 582J 04 Series

Reviews:

Brands by name

Popular brands

Bryant 582J 04 Series, Installation Instructions Manual

Search results

Summary of Contents for 582J 04 Series

Reviews:

Brands by name

Popular brands