manualshive.com logo in svg

Bryant 582J 04 Series, Installation Instructions Manual

Share
Download
Bryant 582J 04 Series Installation Instructions Manual Download Page 41

41

C09302

Fig. 61 -- EconoMi$er

R

IV Wiring

Step 14 — Adjust Factory--Installed Options

Smoke Detectors —

Smoke detector(s) will be connected at the Controls

Connections Board, at terminals marked “Smoke

Shutdown”. Cut jumper JMP 3 when ready to energize

unit.

EconoMi$er IV Occupancy Switch —

Refer to Fig. 61 for general EconoMi$er IV wiring.

External occupancy control is managed through a

connection on the Controls Connections Board.

If external occupancy control is desired, connect a time

clock or remotely controlled switch (closed for Occupied,

open for Unoccupied sequence) at terminals marked

OCCUPANCY. Cut jumper JMP 2 to complete the

installation.

Step 15 — Install Accessories

Available accessories include:

Curb
Thru--base connection kit (must be installed before unit

is set on curb)
LP conversion kit
Flue discharge deflector

Manual outside air damper
Two--Position motorized outside air damper
EconoMi$er X (with control)
EconoMi$er IV (with control)
EconoMi$er2 (without control/for external signal)
Power Exhaust
Differential dry--bulb sensor (EconoMi$er IV)
Outdoor enthalpy sensor
Differential enthalpy sensor
CO

2

sensor

Louvered hail guard
Motormaster head pressure controls
Phase monitor control

Refer to separate installation instructions for information

on installing these accessories.

Pre--Start and Start--Up

—

This completes the mechanical installation of the unit.

Refer to the unit’s Service Manual for detailed Pre--Start

and Start--Up instructions. Download the latest versions

from HVAC Partners (www.hvacpartners.com).

582J

Summary of Contents for 582J 04 Series













































Reviews:

No comments

Brands by name

Popular brands

Load more brands