manualshive.com logo in svg

Bryant 582J 04 Series, Installation Instructions Manual

Share
Download
Bryant 582J 04 Series Installation Instructions Manual Download Page 14

14

4. Carefully lift the hood assembly (with metal tray)

through the filter access opening and assemble per the

steps outlined in

Economizer Hood and Two–Position

Hood,

below.

Economizer Hood and Two--Position Hood —
NOTE

: If the power exhaust accessory is to be installed

on the unit, the hood shipped with the unit will not be
used and must be discarded. Save the aluminum filter for
use in the power exhaust hood assembly.

1. The indoor coil access panel will be used as the top of

the hood. Remove the screws along the sides and bot-

tom of the indoor coil access panel. See Fig. 10.

TOP
PANEL

INDOOR
COIL
ACCESS
PANEL

INDOOR
COIL
ACCESS
PANEL

CAULK
HERE

TOP
PANEL

C06025

Fig. 10 -- Indoor Coil Access Panel Relocation

2. Swing out indoor coil access panel and insert the hood

sides under the panel (hood top). Use the screws

provided to attach the hood sides to the hood top. Use

screws provided to attach the hood sides to the unit. See

Fig. 11.

B

TOP
PANEL

INDOOR COIL
ACCESS PANEL

19 1/16”

SCREW

HOOD DIVIDER

LEFT
HOOD
SIDE

33 3/8”

(848mm)

(483mm)

C06026

Fig. 11 -- Economizer Hood Construction

3. Remove the shipping tape holding the economizer

barometric relief damper in place (economizer only).

4. Insert the hood divider between the hood sides. See

Fig. 11 and 12. Secure hood divider with 2 screws on

each hood side. The hood divider is also used as the

bottom filter rack for the aluminum filter.

5. Open the filter clips which are located underneath the

hood top. Insert the aluminum filter into the bottom

filter rack (hood divider). Push the filter into position

past the open filter clips. Close the filter clips to lock

the filter into place. See Fig. 12.

6. Caulk the ends of the joint between the unit top panel

and the hood top.

7. Replace the filter access panel.

DIVIDER

BAROMETRIC
RELIEF

CLEANABLE
ALUMINUM
FILTER

FILTER

HOOD

FILTER
CLIP

OUTSIDE
AIR

C08634

Fig. 12 -- Economizer Filter Installation

Step 9 — Units with Hinged Panels Only

Relocate

latch

shipped

inside

the

compressor

compartment behind the hinged compressor door to

location shown in Fig. 13 after unit installation.

If the unit does not have hinged panels, skip this step and

continue at step 10.

C12101

Fig. 13 -- Compressor Door Latch Location

582J

Summary of Contents for 582J 04 Series













































Reviews:

No comments

Brands by name

Popular brands

Load more brands