manualshive.com logo in svg

Bryant 582J 04 Series, Installation Instructions Manual

Share
Download
Bryant 582J 04 Series Installation Instructions Manual Download Page 3

3

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could cause personal

injury or death.
Before performing service or maintenance operations

on unit, always turn off main power switch to unit and

install lock(s) and lockout tag(s). Unit may have more

than one power switch.

!

WARNING

UNIT OPERATION AND SAFETY HAZARD

Failure to follow this warning could cause personal

injury, death and/or equipment damage.
Puron

r

(R--410A) refrigerant systems operate at

higher pressures than standard R--22 systems. Do not

use R--22 service equipment or components on Puron

refrigerant equipment.

!

WARNING

PERSONAL INJURY AND ENVIRONMENTAL

HAZARD

Failure to follow this warning could cause personal

injury or death.
Relieve pressure and recover all refrigerant before

system repair or final unit disposal.
Wear safety glasses and gloves when handling

refrigerants. Keep torches and other ignition sources

away from refrigerants and oils.

!

WARNING

CUT HAZARD

Failure to follow this caution may result in personal

injury.

Sheet metal parts may have sharp edges or burrs. Use

care and wear appropriate protective clothing, safety

glasses and gloves when handling parts and servicing

air conditioning equipment.

CAUTION

!

Rated Indoor Airflow (cfm)

The following table lists the rated indoor airflow used for

the AHRI efficiency rating for the units covered in this

document.

Model Number

Full Load Airflow (cfm)

582J*04

1050

582J*05

1400

582J*06

1750

582J

Summary of Contents for 582J 04 Series













































Reviews:

No comments

Brands by name

Popular brands

Load more brands