manualshive.com logo in svg

Brother MFC-8370DN, User Manual

Share
Download
Brother MFC-8370DN User Manual Download Page 143

Troubleshooting and routine maintenance

133

C

Cooling Down

Wait for a while

The temperature of the drum unit 
or toner cartridge is too hot. The 
machine will pause its current 
print job and go into cooling down 
mode. During the cooling down 
mode, you will hear the cooling 
fan running while the LCD shows 

Cooling Down

, and 

Wait for a while

.

Make sure that you can hear the fan in the 
machine spinning and that the exhaust outlet 
is not blocked by something.

If the fan is spinning, remove any obstacles 
that surround the exhaust outlet, and then 
leave the machine turned on but do not use 
it for several minutes.

If the fan is not spinning disconnect the 
machine from the power for several minutes, 
then reconnect it. (The machine can be 
turned off for up to 60 hours without losing 
faxes stored in the memory. See 

Transferring your faxes or Fax Journal report

 

on page 137.)

Cover is Open

The front cover is not closed 
completely.

Close the front cover of the machine.

Cover is Open

The fuser cover is not closed 
completely or paper was jammed 
in the back of the machine when 
you turned on the power.

„

Close the fuser cover of the machine.

„

Make sure paper is not jammed inside 
the back of the machine, and then close 
the fuser cover and press 

Start

.

Cover is Open

The ADF cover is not closed 
completely.

Close the ADF cover.

The ADF is open while loading a 
document.

Close the ADF cover of the machine and 
press 

Stop/Exit

.

Disconnected

The other person or other 
person’s fax machine stopped the 
call.

Try to send or receive again.

Document Jam

The document was not inserted 
or fed correctly, or the document 
scanned from the ADF was too 
long.

See 

Document jams

 on page 138 or 

Using 

the automatic document feeder (ADF)

 

on page 19.

DR mode in Use

(except New Zealand)

The machine is set to Distinctive 
Ring mode. You can not change 
the Receive Mode from Manual to 
another mode.

Set Distinctive Ring to off.

For Austlaria, see 

Telstra

®

 FaxStream

®

 

Duet

®

 (Distinctive Ringing)

 on page 51.

For Other countries, see 

Distinctive Ringing 

(For Singapore and Hong Kong)

 on page 56.

Faxability On

For New Zealand

The machine is set to Faxability 
mode. You can not change the 
Recieve Mode from Manual to 
another mode.

Set Faxability to off.

See 

FaxAbility

 on page 54.

Drum Error

The corona wire on the drum unit 
needs to be cleaned.

Clean the corona wire on the drum unit. (See 

Cleaning the corona wire

 on page 149.)

The drum unit has reached the 
end of its life.

Replace the drum unit. (See 

Replacing the 

drum unit

 on page 157.)

Error Message

Cause

Action

Summary of Contents for MFC-8370DN
























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands