Home
/
Brother
/
MFC-8370DN
/
User Manual

Brother MFC-8370DN, User Manual

Share

Page: 142 / 215

Brother MFC-8370DN User Manual Download Page 142

132

Error and maintenance messages

C

As with any sophisticated office product, errors may occur and consumable items may need to be
replaced. If this happens, your machine identifies the error or required routine maintenance and
shows the appropriate message. The most common error and maintenance messages are shown
below.

You can clear most errors and perform routine maintenance messages by yourself. If you need
more help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips.

Visit us at http://solutions.brother.com/.

Error Message

Cause

Action

20 Sheet Limit

The ADF output tray has reached
its maximum capacity.

Do one of the following:

To send the pages scanned so far, press

1.Send

.

To delete the scanned pages, press

2.Delete

.

If you send the pages already scanned and
want to send the remaining pages, remove
the scanned sheets from the ADF output
tray, then dial the fax number (if you are
sending a fax) and press

Start

.

Access Error

The device is removed from the
USB direct interface while the
data is processing.

Press

Stop/Exit

. Reinsert the device and try

to print with Direct Print.

Cartridge Error

The toner cartridge is not installed
correctly.

Pull out the drum unit, take out the toner
cartridge and put it back into the drum unit
again.

Comm.Error

Poor telephone line quality
caused a communication error.

Try sending the fax again or try connecting
the machine to another telephone line. If the
problem continues, call the telephone
company and ask them to check your
telephone line.

Connection Fail

You tried to poll a fax machine
that is not in Polled Waiting mode.

Check the other fax machine’s polling setup.

«
...
140
141
142
143
144
...
»

Summary of Contents for MFC-8370DN
























































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands