manualshive.com logo in svg

Brother HL-3040CN, Service Manual, Page: 6 / 437

Share
Download
Brother HL-3040CN Service Manual Download Page 6

iv

Confidential

For USA and Canada

■

Federal Communications Commission (FCC) Declaration of Conformity 
(For USA)

declares, that the products

complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide 
reasonable protection against harmful interference in a residential installation.  This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Important

A shielded interface cable should be used to ensure compliance with the limits for a Class B 
digital device.  Changes or modifications not expressly approved by Brother Industries, Ltd. 
could void the user’s authority to operate the equipment.

■

Industry Canada Compliance Statement (For Canada)

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Responsible Party: 

Brother International Corporation

100 Somerset Corporate Boulevard 

P.O. Box 6911

Bridgewater, NJ 08807-0911

USA

Telephone: (908) 704-1700

Product name:

Printer HL-3040CN and HL-3070CW

Model number: 

HL-30C

Summary of Contents for HL-3040CN






















































































































































































































































































































































































































































Reviews:

No comments