manualshive.com logo in svg

Brother HL-3040CN, Service Manual, Page: 133 / 437

Share
Download
Brother HL-3040CN Service Manual Download Page 133

3-69

Confidential

■

White horizontal stripes on one color image

<

User Check

>

- The problem may disappear by itself.  Try printing multiple pages to clear this problem 

especially if the machine has not been used for a long time.

- Replace the toner cartridge with a new one.

- The drum unit may be damaged.  Replace the drum unit with a new one.

■

Faint print

Step

Cause

Check

Result

Remedy

1

HVPS control PCB 
failure

Is the problem solved 
after replacing the HVPS 
control PCB ASSY?

Yes

Replace the HVPS 
control PCB ASSY.

2

High-voltage power 
supply PCB failure

Is the problem solved 
after replacing the 
high-voltage power 
supply PCB ASSY?

Yes

Replace the 
high-voltage power 
supply PCB ASSY.

3

Engine PCB failure

Is the problem solved 
after replacing the 
engine PCB ASSY?

Yes

Replace the engine 
PCB ASSY.

<

User Check

>

- Open and close the top cover and make print again.

- Check that the machine is installed on a level surface.
- Replace the toner cartridge with a new one.
- Clean the LED array with a soft lint-free cloth.

Step

Cause

Check

Result

Remedy

1

Lifting of LED ASSY

Is printing of the LED 
ASSY test pattern 
correctly done in 

“Function code 68”

?

No

Re-assemble the LED 
ASSY.

2

Toner/new 
sensor PCB failure

Is the “Replace Toner” 
message indicated on 
the LCD when replacing 
the toner cartridge with 
the one which has 
reached the end of life?

No

Replace the toner/new 
sensor PCB ASSY.

Summary of Contents for HL-3040CN






















































































































































































































































































































































































































































Reviews:

No comments