manualshive.com logo in svg

Brother DCP-9055CDN, Service Manual

Share
Download
Brother DCP-9055CDN Service Manual Download Page 52

2-14

Confidential

2.6 Life of Toner Cartridge and Drum Unit

■

Life of toner cartridge

<Method of detecting toner life>

There are two messages, which are displayed on the LCD to indicate that toner reaches 

its life: “Toner Low” and “Replace Toner.”  While “Toner Low” is displayed on the LCD 

when the toner sensor detects a certain amount of toner is used, “Replace Toner” is 

displayed on the LCD when the toner sensor detects that toner is used up or when the 

number of rotations of the developer roller reaches its life.
- Detection by the toner sensor

This machine has a function to detect the remaining toner by checking the level at which 

toner in a cartridge interrupts light using a transmissive light sensor.

- Detection by means of rotation rates of the developer roller reached its upper limit

This machine has a function to detect when the number of rotations reaches the upper 

limit before the developer roller is worn out and becomes unusable.

<Relationship between printable pages of the toner cartridge and remaining toner>

The life of toner cartridges when making prints of the print pattern specified by ISO/IEC 24712 
is shown in the table below. (At the point of

in the figure above)

To avoid problems caused by the worn-out of the developer roller surface and deterioration of 

the toner ceiling, “Replace Toner” message is displayed and the print operation is prohibited 

when the number of the rotations of the developer roller reaches the upper limit even if toner 

remains.  The upper limit of the number of the rotations of the developer roller is shown in the 

table below.

 

Memo:

When the number of rotations of the developer roller reaches the

 

cartridge life end, “Replace Toner” is 

displayed even if toner remains.

Toner cartridge

Number of printable pages

Standard

Black

2,500 

pages

Yellow, Magenta, Cyan

1,500 

pages

High

Black

4,000 

pages

Yellow, Magenta, Cyan

3,500 

pages

Super High

Black

6,000 

pages

Yellow, Magenta, Cyan

6,000 

pages

Toner cartridge

Upper limit of rotations of the developer roller

Standard

Black

72,450 

rotations

Yellow, Magenta, Cyan

43,470 

rotations

High

Black

115,920 

rotations

Yellow, Magenta, Cyan

101,430 

rotations

Super High

Black

173,880 

rotations

Yellow, Magenta, Cyan

173,880 

rotations

Full

Low

Empty

pages

Remaining  
toner

Cartridge Life End

Toner Empty

Toner Empty

Low-duty

High-duty

Normal-duty

(ISO/IEC24712)

2

Summary of Contents for DCP-9055CDN





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands