Home
/
Brother
/
DCP-9055CDN
/
Service Manual

Brother DCP-9055CDN, Service Manual

Share

Page: 400 / 532

Brother DCP-9055CDN Service Manual Download Page 400

5-1

Confidential

1.

MAINTENANCE MODE

The maintenance mode is exclusively designed for the checking, setting and adjustments of
the machine by using the buttons on the control panel. The EEPROM can be customized
according to the destination of the machine. Moreover, the operational check of the LCD,
operation panel board, and sensors, print test, display of the log information and error codes,
and change of the worker switches (WSW) can be performed.

1.1 How to Enter the Maintenance Mode

< Operating procedure>

(1) Press the

Menu

button and then the

Start/Black

button while the machine is in the ready

state. Next, press the

button four times to enter the maintenance mode.

(2) The machine beeps for one second and displays "

" on the LCD,

indicating that it is placed in the initial state of the maintenance mode, a mode in which the
machine is ready to accept entry from the buttons.

(3) To select any of the maintenance mode functions shown in the

, enter the

maintenance mode that you want to use using the buttons.

1.2 How to Enter the End User-accessible Maintenance

Mode

Basically, the maintenance-mode functions listed in the

should be accessed by

service personnel only. However, you can allow end users to access some of these under the
guidance of service personnel by phone, for example.
The end user-accessible functions are

shaded

in the table given on the

09, 10 , 1 1 , 12, 25, 43, 45 , 52 , 53 , 54, 66, 68, 71, 72 , 80 , 82 , 87, 88

and

Function code 10 accesses the firmware switches, each of which has eight selectors.
The service personnel should instruct end users to follow the procedure given below.

< Operating procedure>

(1) Press the

Menu

,

Start/Black

,

Menu

and

buttons in this order when the machine is in

the ready state. "MAINTENANCE 06" appears on the LCD.

(2) Press the

or

button to display the desired maintenance code on the LCD. Then

press the

OK

button.

To switch the machine back to the ready state, press the

Stop/Exit

button. When each of the

user-accessible functions is completed, the machine automatically returns to the ready state.

Memo:

Operation using

Menu

,

*

,

2

,

8

,

6

and

4

buttons is also available.

Memo:

- To exit from the maintenance mode and switch to ready state, press the

9

button twice in

the initial state of the maintenance mode.

- When the

Stop/Exit

button is pressed, the machine beeps for one second and returns to

the initial state of the maintenance mode.

- When an incorrect maintenance mode is entered, the machine beeps for one second and

returns to the initial state of the maintenance mode.

«
...
398
399
400
401
402
...
»

Summary of Contents for DCP-9055CDN





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands