manualshive.com logo in svg

Brother DCP-9055CDN, Service Manual

Share
Download
Brother DCP-9055CDN Service Manual Download Page 394

4-11

Confidential

6.

IF YOU REPLACE THE DRUM DRIVE MOTOR

<What to do when replacing the drum drive motor>

- Alignment of gear phase

When replacing the drum drive motor, the gears listed below are removed.  Align the phase of 
each gear in accordance with the table and figure given below when mounting these gears.

<Gear names>

<Gear phase alignment procedure>

(1) When mounting LY0198001 Drum idle gear Z64 and LY0199001 Drum idle gear Z64 

first of Nos.  1 to 3, mount them by aligning their phases as shown in the figure below.

Fig. 4-2

1

LY0198001

Drum idle gear Z64

2

LY0199001

Drum idle gear Z64 first

3

LY0198001

Drum idle gear Z64

4 to 7

LY0196001

Drum coupling gear Z52

Top drive ASSY

Drum idle gear Z64

Drum idle gear Z64 first

Drum idle gear Z64

Mark

Mark

Mark

Motor gear

Align the phase of the mark 

Align the phase of the mark 

Align the phase of the mark 

Mark on the sheet metal

Mark on the sheet metal

1

2

3

on the gear to the mark on 

on the gear to the center of 

on the gear to the mark on 

the sheet metal.

the Motor gear.

the sheet metal.

Summary of Contents for DCP-9055CDN





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands