Brother CS-8072 Operation Manual Download Page 66

Page: 66 / 82

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

TTERNS

(PR

OGRAMMED IN

CHINE)

Hemstitching 2

2. Pull out several threads from both sides of the 4 mm (3/16'')

area which is not yet open. (Pull out four threads, leave five
threads and then pull out four threads, the width of five threads
is approximately 4 mm (3/16'') or less.)

Approx. 4 mm (3/16'') or less

Four threads (pull out)

Five threads (leave)

3. Sew the decorative stitch on the center of the five threads cre-

ated above.

Using a wing needle is an option.

4. Illustration of finished product.

5. Illustration of finished product.

25 26

27 28

29 30

1. Press the

key to turn on the LED lamp, and press the

stitch pattern switch key to select the stitch for hemstitching.

Check that the stitch pattern switch key's LED lamp is lit.

Lamp is lit

Summary of Contents for CS-8072



















































































Search results

Summary of Contents for CS-8072

Reviews:

Related manuals for CS-8072

Brands by name

Popular brands

Brother CS-8072, Operation Manual

Search results

Summary of Contents for CS-8072

Reviews:

Related manuals for CS-8072

Brands by name

Popular brands