Brother CS-8072 Operation Manual Download Page 17

Page: 17 / 82

4. While holding the end of the thread with your left hand, pass

the thread through the guides in the order shown by the num-
bers.

Note
-

If the thread is pushed down at 1 to make it taut, it can be
passed around the other thread guides more easily.

Incorrectly feeding the thread will result in faulty sewing.

Thread take-up lever

Threading the take-up lever

5. Lower the presser foot.

6. Guide the thread through the needle clamp thread guide.

Needle clamp thread guide

7. When using the auto-threading device, gently pull the thread

towards you.

Needle threader lever

Guide (Large hook)

Lowering the presser foot will engage the automatic tension
and will allow you to grip the thread as you proceed.

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

TTERNS

(PR

OGRAMMED IN

CHINE)

Summary of Contents for CS-8072



















































































Search results

Summary of Contents for CS-8072

Reviews:

Related manuals for CS-8072

Brands by name

Popular brands

Brother CS-8072, Operation Manual

Search results

Summary of Contents for CS-8072

Reviews:

Related manuals for CS-8072

Brands by name

Popular brands