Brother CS-8072 Operation Manual Download Page 4 | Manualshive

Page: 4 / 82

background image

1

CONGRATULATIONS ON CHOOSING
OUR MACHINE

Your machine is the most advanced computerized household sewing machine.
To fully enjoy all the features incorporated, we suggest that you study the manual.

PLEASE READ BEFORE USING THIS MACHINE

For safe operation
1. Be sure to keep your eye on the needle while sewing. Do not touch the balance wheel, thread

take-up, needle, or other moving parts.

2. Remember to turn off the power switch and unplug the cord when:

•

Operation is completed

•

Replacing or removing the needle or any other parts

•

A power failure occurs during use

•

Maintaining the machine

•

Leaving the machine unattended.

3. Do not store anything on the foot controller.
4. Plug the machine directly into the wall. Do not use extension cords.

For a longer service life
1. When storing this machine, avoid direct sunlight and high humidity locations. Do not use or

store the machine near a space heater, iron, halogen lamp, or other hot objects.

2. Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring pow-

ders can damage the case and machine, and should never be used.

3. Do not drop or hit the machine.
4. Always consult the operation manual when replacing or installing any assemblies, the presser

feet, needle, or other parts to assure correct installation.

For repair or adjustment
In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in
the back of the operation manual to inspect and adjust the machine yourself. If the problem per-
sists, please consult your local authorized Brother dealer.

For additional product information and updates, visit our web site at www.brother.com

«
...
2
3
4
5
6
...
»

Summary of Contents for CS-8072



















































































Reviews:

No comments

Related manuals for CS-8072

Brand: Janome Pages: 32

Brand: Jack Pages: 20

Brand: Vector Fog Pages: 10

Brand: Necchi Pages: 122

Brand: U.S. Products Pages: 12

Brand: Wilson Electronics Pages: 20

Brand: Fimap Pages: 19

Brand: Digital Finishing Group Pages: 6

RIP-R-STRIPPER FCS16

Brand: General Equipment Pages: 63

Brand: Singer Pages: 24

Brand: R+M Suttner Pages: 2

Brand: Samyung Pages: 87

Brand: FONESTAR Pages: 16

Brand: Xerox Pages: 92

Brand: Janome Pages: 42

E12327-00 BIG BERTHA XSM30

Brand: BETCO Pages: 36

GBC/VeloBind System Three Pro

Brand: Officezone Pages: 7

PerfectCool Cielo

Brand: IDROBASE Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands