Brother CS-8072 Operation Manual Download Page 29 | Manualshive

Page: 29 / 82

background image

26

*

For transparent nylon thread, always use needle 90/14 - 100/16.

*

The same thread is usually used for the bobbin thread and upper threading.

FABRIC/THREAD/NEEDLE COMBINATION CHART

About the Needle
The sewing machine needle is probably the most important part of the sewing machine. Choosing the proper
needle for your sewing project will result in a beautiful finish and fewer problems. Below are some things to
keep in mind about needles.
•

The smaller the needle number, the smaller the needle. As the numbers increase, the needles get thicker.

•

Use fine needles with lightweight fabrics, and thicker needles with heavyweight fabrics.

•

To avoid skipped stitches, use ball point needle (golden colored) 90/14 with stretch fabrics.

•

To avoid skipped stitches when sewing decorative stitches, we recommend using the ballpoint needle
(golden colored).

•

A home sewing machine needle 75/11 is inserted in the sewing machine.

CAUTION

Be sure to follow the needle, thread, and fabric combinations listed in the table. Using an
improper combination, especially a heavyweight fabric (i.e., denim) with a small needle (i.e.,
65/9 - 75/11), may cause the needle to bend or break, and lead to injury. Also, the seam may
be uneven, the fabric may pucker, or the machine may skip stitches.

Medium weight fabric

Lightweight fabric

Heavyweight fabric

Stretch fabric

Easily frayed fabric

For top stitching

Cotton
Synthetic mercerized
Silk or silk finished

Cotton
Synthetic mercerized
Silk
Cotton
Synthetic mercerized
Silk
Thread for knits

Cotton
Synthetic mercerized
Silk
Synthetic mercerized
Silk

Fabric

Broadcloth
Taffeta
Flannel,
Gabardine
Lawn, Batiste
Georgette
Challis, Satin
Denim
Corduroy
Tweed
Jersey
Tricot

60 - 80
60 - 80
50 - 80

60 - 80
60 - 80
50 - 80
30 - 50

50
50

50 - 60

50-80
50-80
50-80

30
30

75/11 - 90/14

65/9 - 75/11

90/14 - 100/16

Ball point needle

(golden colored)

75/11 - 90/14

65/9-90/14

90/14 - 100/16

Size

Thread

Size of needle

Type

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

T

P

A

TTERNS

(PR

OGRAMMED IN

MA

CHINE)

«
...
27
28
29
30
31
...
»

Summary of Contents for CS-8072



















































































Reviews:

No comments

Related manuals for CS-8072

Brand: Janome Pages: 25

Brand: Fellowes Pages: 9

Brand: Fellowes Pages: 5

Brand: Fellowes Pages: 6

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 76

Brand: Fellowes Pages: 6

Brand: Fellowes Pages: 8

Brand: Fellowes Pages: 74

Brand: Ice Pages: 33

Brand: Oki Pages: 923

Brand: Oki Pages: 1020

Brand: DFG Pages: 5

Coronet BLCT16A

Brand: Baby Lock Pages: 62

Brand: Tennant Pages: 16

Speed Scrub 2601

Brand: Nobles Pages: 75

Brand: Janome Pages: 94

Brand: Aficio Pages: 300

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands