Brother CS-8072 Operation Manual Download Page 77

Page: 77 / 82

CATEGORY

NAME OF PATTERN

PATTERN

TYPE

OF PRESSER FOOT

USE

REINFORCEMENT

STITCHING

STITCH ADJUSTMENT BY

STITCH WIDTH KEYS

STITCH ADJUSTMENT BY

STITCH LENGTH KEYS

DECORA

TIVE STITCH

DECORATIVE

STITCH

For decoration, etc.

R :

The machine sews in reverse while the “REVERSE STITCH” button is pushed.

The machine sews three reinforcement stitches and stops when the “REVERSE STITCH” button is
pushed.

Adjustments can be made.

– :

Adjustments cannot be made.

TWIN NEEDLE

POSSIBILITY

CAUTION

Make sure to use the correct presser foot for each stitch pattern. Otherwise, the needle may
strike the presser foot and bend or break, causing injury.

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

TTERNS

(PR

OGRAMMED IN

CHINE)

Summary of Contents for CS-8072



















































































Search results

Summary of Contents for CS-8072

Reviews:

Related manuals for CS-8072

Brands by name

Popular brands

Brother CS-8072, Operation Manual

Search results

Summary of Contents for CS-8072

Reviews:

Related manuals for CS-8072

Brands by name

Popular brands