background image

4

www.bromicheating.com

IMpORTANT NOTES AND WARNINGS

WarnInG

• 

THIS APPLIANCE SHALL NOT BE INSTALLED OR USED 
IN RESIDENTIAL DOMESTIC INDOOR AREAS

• 

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE 
HAZARDS OF HIGH SURFACE TEMPERATURES AND 
SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING 
IGNITION

• 

YOUNG CHILDREN SHOULD BE CAREFULLY 
SUPERVISED WHEN THEY ARE IN THE AREA OF THE 
HEATER

• 

DO NOT USE OR STORE FLAMMABLE MATERIALS 
NEAR THIS APPLIANCE

• 

CLOTHING OR FLAMMABLE MATERIALS SHOULD NOT 
BE HUNG FROM THE HEATER OR PLACED ON OR 
NEAR THE HEATER

• 

DO NOT SPRAY AEROSOLS OR FLAMMABLE MATERIALS 
IN THE VACINITY OF THIS APPLIANCE WHILE IT IS IN 
OPERATION

• 

ANY GUARD OR OTHER PROTECTIVE DEVICE 
REMOVED FOR SERVICING THE HEATER (conducted by 
an authorized person) MUST BE REPLACED PRIOR TO 
OPERATING THE HEATER

• 

INSTALLATION AND REPAIR SHOULD BE DONE BY A 
QUALIFIED SERVICE PERSON. THE HEATER SHOULD 
BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY 
BY A QUALIFIED SERVICE PERSON

Failure to follow the warnings and instructions in this manual 
could result in severe personal injury, death or property 
damage.

• 

This Installation, Operation and Maintenance manual 
should not be removed from the site of installation.

• 

Installer should leave manual with the customer for future 
reference.

• 

This Appliance is for outdoor areas only. (see attached 
diagrammatical representations of outdoor areas 
“Appendix A”).

• 

Do not perform maintenance until heater has been 
turned off, power disconnected, and heater temperature 
has cooled to room temperature.

• 

Do not expose the burner to water or moisture. 

THE 

AppLIANCE IS TO BE pROTECTED FROM RAIN.

• 

Do not use the heater if any of these parts are exposed 
to water until the appliance is inspected or repaired by 
an authorized service person.

• 

The installer is to ensure that the requirements of the local 
authority, local gas fitting regulations, municipal building 
codes, and any other relevant statutory regulations are 
carried out.

• 

Certain materials or items, when stored under or near the 
appliance, will be subjected to radiant heat and could 
be seriously damaged. Ensure combustible materials eg. 
overhead structures, walls, floors, furniture, fixtures and 
plants are kept at least 3ft from the top and side.

• 

The whole gas system, hose assembly, regulator, pipes, 
and burner should be inspected for damage and leaks 
before use and at least annually by an authorized person 
for the life of the heater.

• 

All leak tests should be done with a soap solution. Never 
use an open flame to check for leaks.

• 

Do not use the heater until all connections have been 
leak tested by an authorized person.

• 

Inspect the hose assembly before each use of the 
appliance.

• 

The hose assembly must be replaced prior to the 
appliance being put into operation if there is evidence of 
excessive abrasion or wear, or if the hose is damaged.

• 

The replacement hose assembly must be CSA 
approved.

• 

The hose assembly is not to be located in areas where 
the hose may be subject to accidental damage

• 

This radiant heater is NOT intended to be installed on 
recreational vehicles and/or boats.

• 

Repair to be carried out ONLY by an authorized person.

• 

Improper installation, adjustment, or alteration can cause 
personal injury, property damage, or even death.

• 

Do not attempt to alter the unit in any manner.

• 

Remove transit protection before use.

• 

Never operate the heater in an explosive environment 
such as areas where gasorline or other flammable liquids 
or vapours are stored.

• 

Turn off the gas supply immediately if smell of gas is 
detected.

• 

Do not paint any surface of the heater.

• 

Do not throw objects at the heater.

• 

Control compartment, burner and circulation air 
passageways of the heater must be kept clean. Frequent 
cleaning may be required as necessary.

• 

Turn Gas Supply off when not in use.

• 

Check the heater immediately if any of the following 
occurs:

 

»

The heater does not reach temperature.

 

»

The burner makes popping noise during use (a 
slight noise is normal when the burner is ignited or 
extinguished).

• 

Young children should be supervised to ensure that they 

don’t play with the appliance.

• 

This appliance is not intended for use by young or infirm 

persons unless they have been adequately supervised 

by a responsible person to ensure that they can use the 

appliance safely.

• 

Check for damage to the appliance regularly. If damage 

to the cord, plug or appliance is suspected, discontinue 

use immediately and contact the supplier or qualified 

person for repair.

• 

If the cord, plug or appliance is damaged, unplug from 

the outlet, discontinue use immediately, and only an 

authorized person or similar may repair the unit.

• 

Avoid inhaling fumes emitted from the heater’s first 

use. Smoke and odour from the burning of oils used in 

manufacturing will appear. Both the smoke and odour 

will dissipate after approximately 30 minutes.

• 

Ensure that a watertight seal is maintained on the 

electrical control box at all times

• 

Regularly check for damage to the rubber seals. If 

damage to the rubber seals is suspected, discontinue 

use immediately, switch off power and contact the place 
of purchase or authorized service technician for repair.

!

Summary of Contents for PLATINUM 300 BURNER
























































Reviews: