Brocade Communications Systems ICX 6650 series Hardware Installation Manual Download Page 66

Page: 66 / 83

4. Remove the fan tray from the anti-static shielded bag.

CAUTION
Do not force the installation. If the fan assembly does not slide in easily, ensure that it is correctly oriented before
continuing.

5. Holding the fan tray level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it

firmly engages with the connector.

6. When you are sure the fan tray has properly engaged the connector, tighten the captive screw to secure the fan tray in the slot.

NOTE

The fans are controlled automatically by the device .

7. Verify correct installation by running the

show chassis

command, as shown in the following example:

device#show chassis

The stack unit 1 chassis info:

Power supply 1 (AC - Regular) present, status ok

Model Number: 23-0000144-01

Serial Number: 028

Firmware Ver: A

Power supply 1 Fan Air Flow Direction: Front to Back

Power supply 2 not present

Fan 1 ok, speed (auto): [[1]]<->2

Fan 2 ok, speed (auto): [[1]]<->2

Fan controlled temperature: 37.5 deg-C

Fan speed switching temperature thresholds:

Speed 1: NM<----->70 deg-C

Speed 2: 65<-----> 85 deg-C (shutdown)

Fan 1 Air Flow Direction: Front to Back

Fan 2 Air Flow Direction: Front to Back

MAC-Back Temperature Readings:

Current temperature : 37.5 deg-C

MAC-Left Temperature Readings:

Current temperature : 34.0 deg-C

MAC-Right Temperature Readings:

Current temperature : 33.0 deg-C

MAC-Front Temperature Readings:

Current temperature : 33.0 deg-C

CPU Temperature Readings:

Current temperature : 37.5 deg-C

Center Temperature Readings:

Current temperature : 30.5 deg-C

sensor A Temperature Readings:

Current temperature : 37.5 deg-C

sensor B Temperature Readings:

Current temperature : 31.0 deg-C

sensor C Temperature Readings:

Current temperature : 34.5 deg-C

sensor D Temperature Readings:

Current temperature : 30.5 deg-C

Warning level.......: 45.0 deg-C

Shutdown level......: 85.0 deg-C

Boot Prom MAC : 748e.f893.eabe

Management MAC: 748e.f893.eabe

CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in place. If you run the
chassis with an uncovered slot, the system will overheat.

Replacing fan trays

Brocade ICX 6650 Hardware Installation Guide

Part Number: 53-1003621-04

Summary of Contents for ICX 6650 series




















































































Search results

Summary of Contents for ICX 6650 series

Reviews:

Related manuals for ICX 6650 series

Brands by name

Popular brands

Brocade Communications Systems ICX 6650 series, Hardware Installation Manual

Search results

Summary of Contents for ICX 6650 series

Reviews:

Related manuals for ICX 6650 series

Brands by name

Popular brands