Brocade Communications Systems ICX 6650 series Hardware Installation Manual Download Page 38

Page: 38 / 83

Brocade recommends using an ESD wrist strap during installation.

DANGER

For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

1. Ensure the power on the DC power supply is switched off.
2. Remove the previously installed power supply from the appropriate slot by removing the chassis attachment screws located in

the upper right and lower left of the power supply unit using a flat-head screwdriver.

FIGURE 20

DC power supply screws

1 Chassis attachment screws
2 Assembly screws

3. Before opening the package that contains the DC power supply, touch the bag to the switch casing to discharge any potential

static electricity.

4. Remove the DC power supply from the anti-static shielded bag.

Power supplies

Brocade ICX 6650 Hardware Installation Guide

Part Number: 53-1003621-04

Summary of Contents for ICX 6650 series




















































































Search results

Summary of Contents for ICX 6650 series

Reviews:

Related manuals for ICX 6650 series

Brands by name

Popular brands

Brocade Communications Systems ICX 6650 series, Hardware Installation Manual

Search results

Summary of Contents for ICX 6650 series

Reviews:

Related manuals for ICX 6650 series

Brands by name

Popular brands