Broadway Limited Paragon 2 Series Operator'S Manual Download

Page: 27 / 28

Paragon 2

To enable Functions F13-28 using the NCE

Procab system.

NOTE: The NCE system must have software dated March

2007 or later. To check, press “Prog” until “Set CMD

Station” is displayed. Press “Enter”. The software date

will show. If you need to update, NCE will send a new

chip to install in the system for a nominal fee.

With the system on, disconnect the plug from the

handheld. Hold down the “Select Loco” key while

plugging the cable back in. Press “enter” repeatedly

until “Program Option Key Value” is displayed. Press

122, enter. Press Esc.

Now, pressing the option key 1 time will make keys F1-9

act as 11-19, pressing twice will make keys F1-9 act as

functions 20-29.

Pressing EXPN will now show the status of all 28

functions.

Summary of Contents for Paragon 2 Series





























Search results

Summary of Contents for Paragon 2 Series

Reviews:

Related manuals for Paragon 2 Series

Brands by name

Popular brands

Broadway Limited Paragon 2 Series, Operator'S Manual

Search results

Summary of Contents for Paragon 2 Series

Reviews:

Related manuals for Paragon 2 Series

Brands by name

Popular brands