Self Regulating Heating Cable
© BriskHeat
®
Corporation. All rights reserved.
13
SLCBL Connection / Termination Kits
For use in ordinary locations with SLCBL cable only (UL approved).
For use in roof & gutter snow melting & de-icing applications with SLCBL cable only (UL approved).
Kit Contents:
2
2
1
1
1
Heat-trace warning labels
De-icing snow melt caution labels
Standoff pipe mounting bracket
Lock nut
1/2”NPT Seal fitting with strain relief and grommet
3
1
1
2
1
1
Wire nuts
Black heat-shrink tube 1/2” x 1” (13mm x 25mm)
Green/Yellow heat-shrink tube 1/4” x 6” (6mm x 15cm)
Black heat-shrink tubes 1/8” x 5-1/2” (3mm x 14cm)
Sealing gasket
End seal
Enough to complete:
One input power connection and one end seal termination.
NOTE: Junction box and pipe strap sold seperately. Requires UL Listed junction box suitable for the location with a clearance hole for 1/2” conduit or
1/2” NPT thread hub. For heating cable with no outer-jacket (Type -B only), a metallic junction box must be used to ensure proper grounding.
SLCBLUC:
SLCBL Power Connection Kit
Approvals valid only when
used with appropriate heating cable and installation accessories,
and installed in accordance with all applicable instructions, codes, and regulations.
Kit Contents:
2
2
1
2
2
2
1
Heat-trace warning labels
De-icing snow melt caution labels
Cloth tape
Mastic strips
Clamp ties
Crimp-on insulated terminals
Crimp-on non-insulated barrel
1
1
2
1
1
1
Heat-shrink tube 3/4” x 8” (19mm x 20cm)
Heat-shrink tube 3/4” x 5” (19mm x 13cm)
Heat-shrink tubes 1/8” x 1” (3mm x 25mm)
Heat-shrink tube 1/2” x 1” (13mm x 25mm)
Heat-shrink tube 5/16” x 1-1/2” (8mm x 38mm)
Ground fault device with 120V 3-Prong NEMA 5-15 plug
Enough to complete:
One ground-fault protection power input power connection.
SLCBLUC-GF:
Ground Fault Power Connection Kit
Kit Contents:
2
2
Heat-shrink caps
Heat-shrink tubes 3/4” x 5” (19mm x 13cm)
2 Woven braid sleeves 1/2” x 4” (13mm x 10cm)
Enough to complete:
Two end seal terminations.
SLCBLKC:
SLCBL End Seal Kit
Kit Contents:
1
3
1
5
Clamp tie
Cable ties
Cloth tape
Matic strips
1
3
6
2
Black heat-shrink tube 1” x 8” (25mm x 20cm)
Black heat-shrink tubes 1/2” x 1” (13mm x 25mm)
Black heat-shrink tubes 1/8” x 1” (3mm x 25mm)
Crimp-on insulated terminals
2
1
1
1
Heat-shrink caps
Heat-shrink tube
Crimp-on non-insulated barrel
End seal
Enough to complete:
One splice connection and one end seal termination or one tee connection and one end seal termination.
NOTE: This kit does not complete an input power connection
SLCBLSK:
SLCBL Splice and Tee Kit
Self Regulating Heating Cable
© BriskHeat
®
Corporation. All rights reserved.
14
SLCBL, SLMCBL, SLHCBL Connection / Termination Kits
For use in Hazardous Area Locations with SLCBL (BP, BF) cable only (CSA approved).
For use in non-hazardous area locations with SLCBL, SLMCBL, SLHCBL cable (non-CSA approved).
JHE-GET:
SLCBL, SLMCBL, SLHCBL Low-Profile End Seal Kit
Kit Contents:
1
1
3
End seal housing
Watertight sealing grommet
Pressure seal end with screws
Enough to complete:
One low-profile end seal termination.
Kit Contents:
1
2
2
2
2
In-line splice housing
Watertight sealing gaskets
Housing covers with screws
Watertight sealing grommets
Pressure seal ends with screws
Enough to complete:
One low-profile splice termination.
JHS-GET:
SLCBL, SLMCBL, SLHCBL Low-Profile Splice Connection Kit
JHT-GET:
SLCBL, SLMCBL, SLHCBL Low-Profile Tee Connection Kit
Kit Contents:
1
2
2
3
3
Tee splice housing
Watertight sealing gaskets
Housing covers with screws
Watertight sealing grommets
Pressure seal ends with screws
Enough to complete:
One low-profile tee connection.
NOTE: This kit does not complete an input power connection.
Hazardous (Classified) Locations
Class I, Division 2, Groups A, B, C, D
Class II, Division 2, Groups E, F, G
Class III
Approvals valid only when
used with appropriate heating cable and installation
accessories, and installed in accordance with all applicable instructions, codes, and
regulations.
Kit Contents:
1
1
2
1
1
Octagon junction box with terminal power connections
Pipe standoff mounting bracket
Pipe Straps
Lock nut
Sealing gasket
1
2
1
2
2
M25x1.5 IP68 Seal fitting
Watertight sealing grommets
Watertight sealing plug
Green/Yellow heat-shrink tube 1/4” x 6” (6mm x 15cm)
Black heat-shrink tube 1/8” x 5-1/2” (3mm x 14cm)
Enough to complete:
One input power connection.
PTBO-GET:
SLCBL, SLMCBL, SLHCBL Power Connection Kit With Octagon Enclosure
