15
GB
15
(see Supplement to Operating
Instructions)
3. Technical data
A
Do not use the shredder
when persons (especially
children) or animals are directly
nearby. The user shall be
liable for any damage or injury
incurred.
Never use the shredder when
the protecting devices are
damaged.
Only work in an area where you
have a good view of everything.
Rotating blade assembly !
Blade assembly lags !
Danger of injuries to the
fingers !
During the work, protective
shoes, gloves, and goggles are
to be worn.
The connecting cable installed on
the outside of the shredder must
be examined regularly for signs
of damage and aging (brittle-
ness) and may only be used in
a flawless condition.
When connecting the shredder
using extensions of 2 m in
length only those cables may
be used which are no lighter
than H07 RNF (3 x 1.5 mm
2
)
in accordance with DIN
VDE 0620.
Couplings to the connecting
cable must be of rubber or lined
with rubber and correspond to
the standard DIN VDE 0620.
Use residual current devices
with maximum 30 mA
actuating current or similar
safety devices.
5. Information on safety and hazards
Check contents for completeness
The box should contain the
following parts :
.
Wheel frame
.
Two wheels with hubcaps
.
Motor with gearbox
and cutter unit
.
Hopper tube
.
Hopper top
.
Crossbar
.
Bag with nuts and bolts, tools,
instructions, guarantee card
and list of service centres.
Assembling the shredder
Assembling the wheels
(Fig. 1)
Push washer (item 2) and the
spacer tube (item 3) onto hex-
agonal bolt (item 1) and into
wheel hub (item 4). Then fit
washer (item 5) on bolt (item 1)
and insert the complete assembly
through hole in frame (item 6).
Fit washer (item 7), spring
washer (item 8) and nut (item 9)
onto axle assembly. Fit hubcap
(item 10) onto wheel.
Assembling the motor unit
(Fig. 2)
Place wheel frame (item 1) on
its back as shown. Stand motor
unit (item 2) on its end as shown.
Locate the control pin (item 3)
as shown in cross-shaped open-
ing in the motor unit housing
(item 2). Attach motor unit to
frame as follows: Fit two bolts
(item 4) and tighten as shown.
Place washer (item 6) on long
bolt (item 5) and fit as shown.
Fit bolt (item 7) as shown.
Assembling the crossbar
(Fig. 3)
Locate crossbar (item 1) over
holes in frame and fit with bolts
(item 2). Push plastic caps
(item 3) from bottom into holes
in frame.
Fitting the collector box
(Fig. 4)
Locate collector box on rails
(item 1) and push in fully. The
shredder will only run when
the collector box has been fully
pushed in. Locate the hopper
tube on cutter opening (Fig. 5,
item 1) and fit bolts to motor
unit (Fig. 5, item 2).
Assembling the hopper
2000 ESK
(Fig. 5)
Fit the three square nuts (Fig. 5,
item 3) into the slots provided
in the hopper tube. Place hopper
top (Fig. 5, item 4) on hopper
tube and fit screws provided
(Fig. 5, item 5).
Assembling the hopper
2300 ESK
(Fig. 5)
Place hopper top (item 4) on
hopper tube (item 1). Fit bolts
(item 5) from inside and nuts
(item 5) from outside.
A
Always conduct a visual
check before use to
establish whether any nuts,
bolts, and other parts are worn
or damaged. Worn or damaged
parts are to be replaced.
The manufacturer’s information
on installation is to be observed.
4. Assembly instructions
