manualshive.com logo in svg

brent 16, Owner'S Manual, Page: 14 / 24

Share
Download
brent 16 Owner'S Manual Download Page 14

14

brentwheels.com

SLOW BLOW FUSE  

REPLACEMENT AND INFORMATION

The slow blow fuse is located near the power 
switch on the side of the ie series wheels. Push 
and turn the cap labeled “fuse” to remove. The 
cap should come out easily with the slow blow 
fuse attached. Pull on slow blow fuse to remove 
from cap. Refer to chart for replacement slow 
blow fuse. Push the cap in and turn to lock the 
new slow blow fuse into place.

FUSE LOCATION

MODEL

VOLTAGE

FUSE TYPE (SLOW BLOW)

ie

110-120V

6 Amp Slow Blow

220-240V

6 Amp Slow Blow

ie-r

110-120V

6 Amp Slow Blow

ie-x

110-120V

6 Amp Slow Blow

220-240V

6 Amp Slow Blow

B

110-120C

20 Amp Slow Blow

220-240V

25 Amp Slow Blow

C

110-120V

20 Amp Slow Blow

220-240V

25 Amp Slow Blow

CXC

110-120V

20 Amp Slow Blow

220-240V

25 Amp Slow Blow

EX

110-120V

25 Amp Slow Blow

#16

110-120V

20 Amp Slow Blow

220-240V

25 Amp Slow Blow

REPLACING 

THE SLOW 

BLOW FUSE OF 

MODELS:  

B, C, CXC,  

EX, and #16

REPLACING 

THE SLOW 

BLOW FUSE OF 

MODELS:  

IE, IE-R, and IE-X

SLOW 

BLOW FUSE 

INFORMATION

All slow blow fuses are  

1.25" x .25" or 6.35 x 31.75mm

CAUTION: UNPLUG THE POWER PRIOR  

TO REPLACING THE SLOW BLOW FUSE!

Remove (4) screws from the power cable side 
of the control box. The slow blow fuse will be 
behind the cover. Carefully remove the slow blow 
fuse, a tool may be needed to gently pry the slow 
blow fuse out of the socket.

Summary of Contents for 16

























Reviews:

No comments