90
Q
Navodila za uporabo
POSTAVLJANJE/PRITRJEVANJE SVETILKE
S pomočjo večstopenjsko razstavljivega ročaja lahko po potrebi prilagodimo kot nagiba svetilke
Svetilko lahko z ročajem obesimo tudi na ustrezen kavelj.
Svetilko lahko pritrdite na magnetno držalo na kovinske površine, odvisno od tega ali je v obseg
dobave vključeno magnetno držalo ali ne. V ta namen preprosto pridtrdite magnetno držalo na
ročaj svetilke. Prosimo, bodite pozorni na trdno nasedanje magnetnega držala, da preprečite
morebitne poškodbe ob padcu svetilke.
6
D
Operating Instructions
Rechargeable LED work lamp
• Keep children away from the lamp.
Children are unable to assess the dangers of electric current.
• Use only the recommended power supply unit to charge the batteries.
Using other power supply units can damage the batteries or result in an explosion!
• Switch the lamp off before you clean it. Clean the lamp regularly with a dry, lint-free cloth.
To remove dirt, a damp cloth can be used. Do not use any solvents, caustic cleaning agents, etc.
• Do not look directly at the light to avoid being blinded.
Hot surface
SET-UP/ MOUNTNG THE LAMP:
Using the multi-level, folding bracket, the tilt angle of the lamp can be adjusted as needed.
The lamp can be hung up on a hook using the bracket.
The lamp can be attached to metallic surfaces by means of the magnetic holder which, depending
on the scope of delivery, is either included or available separately as an accessory. For this purpose,
simply attach the magnetic holder to the bracket of the light. Please ensure that the magnetic
holder is firmly seated in order to avoid possible damages caused by the falling light.
SWITCHING THE LAMP ON/OFF:
Press the button (A) to switch the lamp on.
The lamp will shine at 100% brightness.
If the button is pressed again within 2 seconds,
the lamp will switch to 50% mode.
When selecting 50%, the service life of the lamp extends in
comparison to the 100% setting as it consumes less energy.
Press the button again to switch the lamp off.
BATTERY LEVEL INDICATOR (B):
Displays the current charging status of the battery, or, how much energy is still available.
If all 4 LEDs are lit, the battery is fully charged. If the battery is nearly empty, the LED blinks
5 times and the battery status indicator blinks continuously. Then the lamp will remain lit for
approx. 5-10 minutes, before the deep discharge protection shuts the lamp off. This leaves
enough time to finish working.
1
2
3
(similar to fig�)
B
C
A
D
17P150_Akku_LED_Arbeitsstrahler_0496136_KW1219.indd 6
16.03.19 13:12
ZAČETEK UPORABE
• Pred prvo uporabo baterijo najprej popolnoma izpraznite in nato ponovno napolnite.
• Med polnjenjem izdelka ni mogoče uporabljati.
• Če izdelka dalj časa ne uporabljate je treba baterijo napolniti vsake 3 mesece.
• Baterije ni mogoče zamenjati. Ob okvarjeni bateriji je treba reflektor odložiti na ustrezen način.
PREGLED UPRAVLJALNIH ELEMENTOV
Stikalo za vklop/izklop napajanja in zatemnitev:
Enkraten pritisk: Reflektor zasveti z zadnjo nastavljeno močjo, z večkratnim pritiskom
lahko moč svetlobe nastavljate v 5 stopnjah.
Če stikala ne aktivirate več kot 5 sekund, potem se reflektor ob ponovnem aktiviranju
izklopi, neodvisno od nazadnje nastavljene svetlosti.
Stikalo za prikaz polnosti baterije:
Ob vklopu reflektorja se prikaže polnost baterije v %.
Ob izklopljenem reflektorju lahko polnost baterije prikažete z aktiviranjem stikala s
simbolom baterije. Ta bo tako dolgo prikazana, dokler stikala ponovno ne pritisnete.
Stikalo za povezavo Bluetooth (samo FUS 3010 MA):
Z vklopom preide reflektor v stanje pripravljenosti Bluetooth.
Stikalo za barvo oddajane svetlobe (samo RUFUS 3020 MA):
Ob vklopu reflektorja se ta vklopi z zadnjo nastavljeno barvo svetlobe.
Z večkratnim pritiskom lahko nastavite želeno barvo svetlobe.
19P087_088 Mobiler Akku LED Akku Strahler Rufus 0532453_2320 200603.indd 90
03.06.2020 12:25:12
