14
When the trigger lock-off is pressed to the left,
the tool will be fully operational. The trigger
lock-off should always be locked off whenever
any adjustments are made or when tool is not
in immediate use.
Non-mar Tip (fi g. 1)
When using this tool on materials that you do
not want to mark, such as wood cladding, use
the plastic non-mar tip (m) over the contact
trip (c).
LED Indicator (fi g. 1)
Your nailer is equipped with two LED indicator
lights (e) located on the back of the tool just below
the back cap. Also refer to to the
Troubleshooting
Guide
for further instruction.
LOW BATTERY
Replace battery with a
charged pack.
HOT PACK
Let the battery cool or
replace it with a cool pack.
JAM/STALL CONDITION
Rotate the stall release
lever to release. Refer to
Stall Release
.
HOT TOOL
Let the tool cool down
before continuing use.
Stall Release (fi g. 1, 3)
If the nailer is used in rigorous application where
all available energy in the motor is used to drive
a fastener, the tool may stall. The driver blade did
not complete the drive cycle and the jam/stall
indicator (e) will flash. Rotate the stall release lever
(f) on the tool and the mechanism will release.
If the driver blade does not automatically return
to the home position, proceed to
Clearing a
Jammed Nail
. If the unit continues to stall please
review the mode selection, material and fastener
length to be sure that it is not too rigorous an
application.
Clearing a Jammed Nail (fi g. 1, 3)
If a nail becomes jammed in the nosepiece, the
jam/stall indicator light (e) will flash.
1. Remove battery pack from tool and engage
trigger safety lock-off (b).
2. Slide the spring-loaded pusher latch (h) to the
base of the magazine to lock it into place and
unload nail strip.
3. Using the hex tool (k) provided, loosen the
two hex bolts (q) at the top of the magazine.
4. Rotate the magazine (g) forward.
5. Remove jammed/bent nail, using pliers if
necessary.
6.
If driver blade is in the down position, rotate
the stall release lever (f) on the top of the
nailer.
NOTE:
If the driver blade will not reset after
rotating the stall release lever, manually
resetting the blade with a long screwdriver
may be necessary.
7. Rotate the magazine back into position under
the nose of the tool and tighten hex bolts (q).
8. Reinsert battery pack.
NOTE:
The tool will disable itself and not reset
until the battery pack has been removed and
reinserted.
9. Reinsert nails into magazine (refer to
Loading
the Tool
).
10. Release the pusher latch (h).
11. Disengage the trigger safety lock-off (b) when
ready to continute nailing.
If nails become jammed in the nosepiece
frequently, have the tool serviced by an
authorised Bostitch service centre.
MAINTENANCE
Your Bostitch power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up can
cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Summary of Contents for BF33
