Graco Hydra-Clean 308511J Instructions-Parts List Manual Download Page 1 | Manualshive

Page: 1 / 10

background image

Hydra-Clean

R

Gun

For use in pressure washing applications with water and cleaning solutions only.

5000 psi (280 bar, 28.0 MPa) Maximum Working Pressure
Part No. 803350 Brass Body
Part No. 804589
Part No. 15T283

4500 psi (314 bar, 13.4 MPa) Maximum Working Pressure
Part No. 803351 Stainless Steel Body
Part No. 15T282

Instructions–Parts List

308511J

Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.

Model 803351 Shown

1
2
3
...
»

Summary of Contents for Hydra-Clean 308511J











Reviews:

No comments

Related manuals for Hydra-Clean 308511J

Brand: PowRyte Pages: 6

Brand: SGS Pages: 7

Brand: Sealey Pages: 3

Brand: Poniie Pages: 5

Brand: Beck Pages: 4

Brand: Parkside Pages: 42

Brand: Parkside Pages: 52

Brand: Craftex Pages: 8

Brand: Central Pneumatic Professional Pages: 12

Brand: Campbell Hausfeld Pages: 24

Brand: pro.point Pages: 39

Brand: Campbell Hausfeld Pages: 24

Brand: DAJ Pages: 12

Brand: Hitachi Pages: 46

Brand: Paslode Pages: 12

Brand: VonHaus Pages: 28

Brand: Senco Pages: 1

Brand: Senco Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands