background image

 

www.bosspac.com 

 

8

FCC & IC Statements 

 
 
FCC Class B Part 15 

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 
• This device may not cause harmful interference, and 
• This device must accept any interference received, including interference that may 
cause undesired operation. 
 
Changes or modifications not expressly approved by BossPacEngineering Technology 
Inc. may void the user’s authority to operate the equipment. 

 
IC RSS 210 

This device complies with Industry Canada licence-exempt RSS standard(s). Operation 
is subject to the following two conditions: (1) this device may not cause interference, 
and (2) this device must accept any interference, including interference that may cause 
undesired operation of the device. 
 
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux 
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions 
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de 
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d'en compromettre le fonctionnement. 

 
FCC/IC RF Exposure Statement 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. 
 
 
Cet équipement est conforme à l'exposition aux radiations de FCC et d'Industrie 
Canada établies pour un environnement non contrôlé. 
 
 

 

 

 

 

Bay 8, 1450 - 28 Street NE,

 

Calgary, Alberta,

 

Canada

  

T2A 7W6 

Phone: +1 (403) 216-1226 Toll Free: +1 (866) 616-1226 Fax: +1 (403) 216-5557

 

Summary of Contents for WASP









Reviews: