Boss Snowplow MSC13625 Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 28

background image

Maintenance

WARNING

Failing to properly maintain the machine could result in premature failure of machine systems,
causing possible harm to you or bystanders.

Keep the machine well maintained and in good working order as indicated in these instructions.

CAUTION

If you leave the key in the switch, someone could accidently start the engine and seriously
injure you or other bystanders.

Remove the key from the switch before you perform any maintenance.

Note:

Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

Before each use or daily

• Check the hydraulic lines and hoses.
• Check the torque of all fasteners, pins, retainers, nuts, and bolts.
• Check the cutting edge.
• Check the wire-harness connector.
• Grease the coupler spring pins.

Before storage

• Grease the lift-cylinder rod.
• Apply dielectric grease to the wire-harness connectors.
• Grease the coupler spring pins.

Monthly

• Apply dielectric grease to the wire-harness connectors.

18

«
...
16
17
18
19
20
...
»

Summary of Contents for MSC13625





























Reviews:

No comments

Related manuals for MSC13625

Brand: PALSON Pages: 32

Brand: Little Wonder Pages: 54

Brand: Powersmart Pages: 25

Flex-Force Power System 51822

Brand: Toro Pages: 16

Brand: Troy-Bilt Pages: 36

Brand: Viking Pages: 8

Brand: Homestead Pages: 15

AIRDROP P Series

Brand: Unigreen Pages: 32

Brand: Worx Pages: 22

Brushless Motor WG569E

Brand: Worx Pages: 104

VAC ATTACK II UT08544

Brand: Homelite Pages: 6

Brand: Homelite Pages: 14

Brand: Homelite Pages: 20

Brand: Homelite Pages: 42

Brand: FUJII Pages: 70

Brand: Maruyama Pages: 20

Brand: FIORENTINI Pages: 25

Brand: Power smart Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands