Bosch WFMC32 Repair Manual Download Page 9 | Manualshive

Page: 9 / 27

background image

Rev 0 (1/17/08)

9

Disassembly

Disassembly

–

–

Front Panel (2)

Front Panel (2)

Front panel tab

Remove front panel

Remove top front panel screws

Remove bottom front panel screws

Note front panel mounting tabs

HINT:

Removing front panel at this point will make

removing front counterweights easier.

HINT:

Front panels are mounted using six (6) plastic tabs

– three (3) on each side. Lift front panels up to remove
them. When reassembling front panels, carefully align tabs
and don’t use excessive force to avoid breaking tabs.

HINT:

Most washer screws require

T-20

Torx

screwdrivers.

T-20 screws

T-20 screws

702_58300000133618_ara_en_a

«
...
7
8
9
10
11
...
»

Summary of Contents for WFMC32




























Reviews:

No comments

Related manuals for WFMC32

Brand: Campbell Hausfeld Pages: 18

Brand: Campbell Hausfeld Pages: 13

Brand: Jackson Pages: 33

Brand: Majestic Appliances Pages: 29

Brand: Kranzle Pages: 18

Brand: unicraft Pages: 18

Brand: Danby Pages: 56

Brand: Gorenje Pages: 45

Brand: Smeg Pages: 17

Brand: Fagor Pages: 26

Brand: Kärcher Pages: 24

Brand: Dual Pumps Pages: 20

Brand: Kärcher Pages: 24

Brand: V-ZUG Pages: 48

Aquarius WDD 756

Brand: Hotpoint Pages: 16

Brand: Gaggenau Pages: 33

Brand: Maytag Pages: 24

Brand: Samsung Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands