Bosch T1 Alternator Repair And Testing Instructions Download Page 7

Page: 7 / 45

Repair and Testing Instructions for T1 Page 7

Alternator 0120 689 552

Edition 001

All rights rest with Robert Bosch Corp, including patent rights. All rights of use of reproduction and publication rest with R. B. Corp.

UA/ASV

04.12.98

T1ALTFinal.DOC

3 Specifications

3.1 Electrical Test Specifications

Interference suppression capacitor

1.8 … 2.6

F (microfarad)

Load current less than/equal to 10A

27.6 … 28.4 V (volts, regulated)

Damping Resistance

3.1 … 3.5 k

(kilohms)

Stator Resistance

0.036

(-0/+10%) T1 (RL) 28V70/140A

Rotor Resistance

7.5

(-0/+10%) T1 (RL) 28V70/140A

Power Output Test

Alternator

Speed (RPM)

Load Current -

Inductive (A)

Test Duration

(Min)

1500

T1 (RL) 28V70/140 A

6000

136

Following completion of the output test, allow alternator to run at 7000 rpm for one minute.

Oscilloscope Pattern

This image represents a properly functioning
alternator. The D.C. voltage produced has a
small harmonic wave.

Small spikes may be superimposed on the
oscilloscope screen if the voltage regulator
is regulating. Applying a load to the
alternator output terminals can turn off the
regulator.

In order to be able to compare oscilloscope
images, the oscilloscope so the pattern fits
between two vertical 10x divisions.

Figure 1 Normal Oscilloscope Pattern

Summary of Contents for T1 Alternator














































Search results

Summary of Contents for T1 Alternator

Reviews:

Related manuals for T1 Alternator

Brands by name

Popular brands

Bosch T1 Alternator, Repair And Testing Instructions

Search results

Summary of Contents for T1 Alternator

Reviews:

Related manuals for T1 Alternator

Brands by name

Popular brands