Bosch T1 Alternator Repair And Testing Instructions Download Page 15 | Manualshive

Page: 15 / 45

background image

Repair and Testing Instructions for T1 Page 15

Alternator 0120 689 552

Edition 001

All rights rest with Robert Bosch Corp, including patent rights. All rights of use of reproduction and publication rest with R. B. Corp.

UA/ASV

04.12.98

T1ALTFinal.DOC

9 Alternator Disassembly and Testing

9.1 Rear Cover Removal

1.

Clamp alternator in clamping fixture KDAW 9999 (Bosch Number 0 986 619 362).

2.

Remove four nuts holding on the air intake cover. (Figure 5)

Figure 5 Air Intake Cover Removal (1)

Note: The voltage regulator must be removed before any further disassembly of the alternator takes place. The

brushes of the regulator can break if the regulator is not removed before any other disassembly takes
place.

9.2 Voltage Regulator Removal

1. Remove the three (3) screws that secure the regulator to the collector ring end shield. (Figure 6)

2. Carefully remove the voltage regulator from the collector ring end shield.

Note: The brushes of the regulator will break if the regulator is not removed before any other disassembly of the

alternator takes place.

«
...
13
14
15
16
17
...
»

Summary of Contents for T1 Alternator














































Reviews:

No comments

Related manuals for T1 Alternator

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: Kawai Pages: 10

Brand: d.s.f. Pages: 8

Brand: YASKAWA Pages: 40

INTEGRA ARINC e-NAV

Brand: Kannad Pages: 20

Brand: HEINE Pages: 4

Brand: Harken Industrial Pages: 6

COVIDAIR S/T EASY

Brand: BCD microtechnique Pages: 21

Brand: Comelit Pages: 8

Brand: Miele professional Pages: 2

Brand: Stamina Pages: 22

Pathport QUATTRO

Brand: Pathway connectivity solutions Pages: 9

Brand: P.Lindberg Pages: 26

Brand: LandStal Pages: 19

Connex Vital Signs Monitor 6000 Series

Brand: Welch Allyn Pages: 143

Brand: WalkAbout Pages: 101

Brand: Advantech Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands