Bosch T1 Alternator Repair And Testing Instructions Download Page 34 | Manualshive

Page: 34 / 45

background image

Repair and Testing Instructions for T1 Page 34

Alternator 0120 689 552

Edition 001

All rights rest with Robert Bosch Corp, including patent rights. All rights of use of reproduction and publication rest with R. B. Corp.

UA/ASV

04.12.98

T1ALTFinal.DOC

4. Align the mounting holes of the regulator to holes of the alternator housing.

Note: When aligning the mounting holes, pay attention to the force used as damage can occur to the brushes.

5. Install the three (3) regulator mounting screws and torque to 1.3 to 1.7 Nm (11.5 to 15 in. lbs.). (Figure 38)

6. Install capacitor on collector end shield and tighten mounting screw to 4.3 to 5.7 Nm (38.0 to 50.4 in. lbs.).

(Figure 38)

7. Connect lead of capacitor to spade te.

8. Install air intake cover onto alternator. Do not torque cover until it has been installed on the vehicle/engine.

Figure 38 Capacitor Installation

(1) Voltage Regulator (2)

«
...
32
33
34
35
36
...
»

Summary of Contents for T1 Alternator














































Reviews:

No comments

Related manuals for T1 Alternator

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Campden instruments Pages: 8

SafetuNet Alert

Brand: Masimo Pages: 2

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: Baoding Longer Precision Pump Pages: 6

Brand: ZIGBEE Pages: 6

Brand: Daisy Pages: 2

Below Ground Pool Cover Box

Brand: Daisy Pages: 3

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Brand: Zodiac Pages: 2

Brand: Zimmer Pages: 46

Brand: GE Pages: 18

Brand: ALL-FILL Pages: 32

ESK+ Manual Knee Lock

Brand: Blatchford Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands