Bosch T1 Alternator Repair And Testing Instructions Download Page 11 | Manualshive

Page: 11 / 45

background image

Repair and Testing Instructions for T1 Page 11

Alternator 0120 689 552

Edition 001

All rights rest with Robert Bosch Corp, including patent rights. All rights of use of reproduction and publication rest with R. B. Corp.

UA/ASV

04.12.98

T1ALTFinal.DOC

6 Parts Cleaning

Caution: Fire Risk

To provide radio interference suppression, the alternator is equipped with capacitors with a long storage time.
Cleaning of alternator components may cause and electrical discharge when they are immersed in cleaning
fluid. This discharge may cause combustible liquids to ignite.

Alternator components with capacitors should only be cleaned with a non-combustible cleaner such as HAKU
1025/6.

Caution: Compressed Air

Only use compressed air regulated to a maximum of 4 Bar (60 PSI), and a clean cloth for cleaning of the
armature, excitation windings and alternator plates.

Caution: Explosion Risk

Avoid exposure to fire, open flame and sparks. Thoroughly dry all cleaned parts as gases could form from the
cleaning process and may cause an explosion.

«
...
9
10
11
12
13
...
»

Summary of Contents for T1 Alternator














































Reviews:

No comments

Related manuals for T1 Alternator

Brand: Handler Pages: 25

Brand: Wahl Pages: 47

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Brand: ParaBody Pages: 5

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

QUICK-ALIGN Vari-Flex

Brand: Össur Pages: 36

Brand: Össur Pages: 2

Brand: Össur Pages: 8

Brand: Calibre Fitness Pages: 11

Brand: Keithley Pages: 57

Brand: Kelso Pages: 21

Brand: Numark Pages: 11

BOMAG BVP 12/50 A

Brand: Fayat Pages: 105

HALO miniLUME LA5300

Brand: Cooper Lighting Pages: 2

Brand: Free The Tone Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands