Event
Code
Description
Event
Code
Description
2 11
Remote Control 4
4
8
Reserved
2 12
Auxiliary Code 1
4
9
Reserved
2 13
Auxiliary Code 2
4 10
Area 1 - Zone Unsealed
2 14
Telephone Line Fail
4 11
Area 2 – Zone Unsealed
2 15
Communications Fail After 3 Attempts
4 12
Area 3 – Zone Unsealed
3 0
Communications Fail
4 13
Area 4 – Zone Unsealed
3 1
Dialler Disabled
4 14
Reserved
3 2
Dialler Active (On-Line)
4 15
Reserved
3 3
Ring Detect (V1.37+)
5
0
Reserved
3 4
Reserved
5
1
AC Main 50 Hz / 60 Hz
3 5
Mimic Zone 1
5
2
Area 1 In Alarm
3 6
Mimic Zone 2
5
3
Area 2 In Alarm
3 7
Mimic Zone 3
5
4
Area 3 In Alarm
3 8
Mimic Zone 4
5
5
Area 4 In Alarm
3 9
Mimic Zone 5
5
6
Area 1 Armed
3 10
Mimic Zone 6
5
7
Area 2 Armed
3 11
Mimic Zone 7
5
8
Area 3 Armed
3 12
Mimic Zone 8
5
9
Area 4 Armed
3 13
Mimic Zone 9
5 10
Area 1 Disarmed
3 14
Mimic Zone 10
5 11
Area 2 Disarmed
3 15
Mimic Zone 11
5 12
Area 3 Disarmed
4 0
Mimic Zone 12
5 13
Area 4 Disarmed
4 1
Mimic Zone 13
5 14
Any Areas Armed
4 2
Mimic Zone 14
5 15
Any Areas Disarmed
4 3
Mimic Zone 15
6
0
Area 1 Codepad Data Terminal
4 4
Mimic Zone 16
6
1
Area 2 Codepad Data Terminal
4 5
Chime
6
2
Area 3 Codepad Data Terminal
4 6
Zone Not Sealed
6
3
Area 4 Codepad Data Terminal
4 7
Reserved
Polarity (Modes)
Option Description Option Description
0
Disabled
7
Reserved
1
Normally Open, Going Low
8
Normally Low, Going Open
2
Normally Open, Pulsing Low
9
Normally Low, Pulsing Open
3
Normally Open, One Shot Low
10
Normally Low, One Shot Open
4
Normally Open, One Shot Low (Reset)
11
Normally Low, One Shot Open (Reset)
5
Normally Open, One Shot Low (Re-trigger)
12
Normally Low, One Shot Open (Re-trigger)
6
Normally Open, Latching Low
13
Normally Low, Latching Open
Time Base
Choose one of the options in the table below for the time base.
Option Description
1
200 ms
2
1 Second
3
1 Minute
4
1 Hour
Time Base Multiplier
Enter a value between 01 – 99.
One Shot Mode
When you program the output polarity as one shot, the time base is multiplied by the time base multiplier (Eg. If
the time base = 2 and the multiplier = 05, the output will operate for 5 seconds)
Pulsing Mode
When you program the output polarity as pulsing, the time base becomes the ‘ON’ time and the multiplier
becomes the ‘OFF’ time. The ‘OFF’ time is the
time base x the multiplier
(Eg. If you want the output to pulse
one (1) second ‘ON’ and five (5) seconds ‘OFF’, you would program time base as one (1) and the multiplier as
five (5)).
14
Solution-16/Solution-16
Safecom
Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC
Bosch Security Systems Pty Limited
