Bosch Rexroth ctrlX CORE X7 Operating Instructions Manual Download Page 39

Page: 39 / 48

39 / 50

ctrlX CORE X7

Fan

Bosch Rexroth AG

R911419122, Edition 01

12.8 USB interface

There are three USB interfaces (type C, USB 3.1) on the front side of the control. The USB interface can

be used to connect USB storage media (only FAT16 and FAT32), scanners and similar USB devices. Not

supported: Display port, Thunderbold, HDMI, USB3.2, USB4.0 and USB PD (power delivery).
Each USB interface provides a voltage supply with DC 5 V and 0.9 A for external devices. The USB

interface is switched off up to the next switch-off and switch-on if the current is exceeded.

The maximum cable length allowed is 3 m.

NOTICE

Device damage due to external supply via the USB interface
The voltage supply grounding (GND (U

)) at the 24 V power connector XD10

always has to be connected.

12.9 Display port

A display port interface with the following specifications is located on the front side of the control:

•

Standard DP++

•

Max. resolution 4096x2304@60 Hz

•

Automatic display detection (AUX channel)

•

Compatible via adapter with DVI and HDMI

•

The display port interface provides a voltage supply with DC 5 V and 0.5 A for external devices.

The maximum cable length allowed is 3 m.

NOTICE

Device damage due to external supply via the display port interface
The voltage supply grounding (GND (U

)) at the 24 V power connector XD10

always has to be connected.

12.10 Battery

A battery is included and working in the device upon delivery. Battery designation: Lithium battery 3.0

V CR1025 (30 mAH).
The battery is used to buffer the real-time clock if the control is disconnected from voltage. A circuit

monitors the battery state.
For notes on changing the battery, see

⮫

Chapter 14.3 “Battery change ” on page 41

A discharged battery causes an incorrect system time.

12.11 Fan

The fan unit, with the two axial fans suitable for industrial use, ensures an optimum cooling of the

ctrlX CORE

PLUS

X7. The fan unit is absolutely essential for its operation. A missing fan unit or a

defective fan can cause overheating and thus the safe shutdown of the ctrlX CORE

PLUS

X7. The fans are

vice descr

tion

Summary of Contents for Rexroth ctrlX CORE X7

















































Search results

Summary of Contents for Rexroth ctrlX CORE X7

Reviews:

Related manuals for Rexroth ctrlX CORE X7

Brands by name

Popular brands

Bosch Rexroth ctrlX CORE X7, Operating Instructions Manual

Search results

Summary of Contents for Rexroth ctrlX CORE X7

Reviews:

Related manuals for Rexroth ctrlX CORE X7

Brands by name

Popular brands