English |
9
Bosch Power Tools
1 609 92A 2WB | (16.2.17)
Technical Data
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Operate your machine only with the auxiliary handle 7
or bow handle 2.
Auxiliary Handle
Screw the auxiliary handle
7
on the right or left of the machine
head depending on the working method.
Bow Handle
Fasten the bow handle
2
to the gear case as shown in the fig-
ure.
Mounting the Grinding Tools
Before any work on the machine itself, pull the mains
plug.
Clean the grinder spindle
6
and all parts to be mounted.
For clamping and loosening the grinding tools, lock the grind-
er spindle with the spindle lock button
3
.
Actuate the spindle lock button only when the grinder
spindle is at a standstill.
Otherwise, the machine may be-
come damaged.
See graphics page for the mounting sequence.
Buffing Disc
Screw the clamping mandrel
8
firmly onto grinder spindle
6
and tighten it via the spanner surfaces with an open-end span-
ner.
Mount the clamping flange
9
and the buffing disc
10
onto the
clamping mandrel
8
. Screw on the clamping nut
11
and tight-
en with the two-pin spanner.
Polishing Plate
Mount the two spacer discs
12
and the polishing plate
13
on-
to the spindle
6
.
Screw on the round nut
14
and tighten with the two-pin span-
ner.
Pull the lamb’s wool bonnet
15
over the polishing plate
13
and tighten the attachment strings.
Polishing Sponge
Screw the polishing sponge
16
firmly onto the grinder spindle
6
. The lambskin polishing bonnet
17
can be pulled over the
polishing sponge
16
.
Rubber Sanding Plate
Place the rubber sanding plate
18
onto the grinder spindle
6
.
Screw on the round nut
14
and tighten with the two-pin span-
ner.
Firmly press the sanding sheet
19
onto the bottom side of the
rubber sanding plate
18
.
Felt Polishing Disc
Firmly screw the felt polishing disc
20
onto the grinder spin-
dle
6
.
Cup Brush/Disc Brush
The cup brush/disc brush must be able to be screwed onto
the grinder spindle until it rests firmly against the grinder
spindle flange at the end of the grinder spindle threads. Tight-
en the cup brush/disc brush with an open-end spanner.
Approved Grinding Tools
All grinding tools mentioned in these operating instructions
can be used.
The permissible speed [min
-1
] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Polisher
GPO 12 CE
Professional
GPO 12 CE
Professional
Article number
3 601 C89 0B0
3 601 C89 0L0
3 601 C89 0J0
3 601 C89 040
3 601 C89 0K0
3 601 C89 0K2
3 601 C89 081
Rated power input
W
1250
1200
Rated speed
min
-1
3000
3000
Speed control adjustment
min
-1
750 – 3000
750 – 3000
Sanding pad diameter, max.
mm
180
180
Thread of grinder spindle
M 14
M 14
Max. spindle length
mm
21
21
Weight according to EPTA-Procedure 01:2014
kg
2.5
2.5
Protection class
/
II
/
II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
OBJ_BUCH-1217-006.book Page 9 Thursday, February 16, 2017 9:13 AM
