8
| English
1 609 92A 2WB | (16.2.17)
Bosch Power Tools
Use special care when working corners, sharp edges,
etc. Avoid bouncing and snagging the accessory.
Cor-
ners, sharp edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback
and loss of control.
Safety warnings specific for sanding operations
Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when select-
ing sanding paper.
Larger sanding paper extending be-
yond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc, or kickback.
Safety warnings specific for polishing operations
Do not allow any loose portion of the polishing bonnet
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings.
Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
Safety warnings specific for wire brushing operations
Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush.
The wire
bristles can easily penetrate light clothing and/or skin.
If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard.
Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
Additional safety warnings
Wear safety goggles.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance.
Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled.
This pre-
vents uncontrolled restarting.
Secure the workpiece.
A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Products sold in GB only:
Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only:
Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for polishing and brushing metal and
coated surfaces as well as for polishing stone without the use
of water.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1
Fastening screw for bow handle
2
Bow handle (insulated gripping surface)
3
Spindle lock button
4
Thumbwheel for speed preselection
5
On/Off switch
6
Grinder spindle
7
Auxiliary handle (insulated gripping surface)*
8
Clamping mandrel*
9
Clamping flange*
10
Buffing disc*
11
Clamping nut*
12
Spacer discs*
13
Polishing plate*
14
Round nut*
15
Lamb’s wool bonnet for polishing plate*
16
Polishing sponge*
17
Lambskin polishing bonnet for polishing sponge*
18
Rubber sanding plate*
19
Sanding sheet*
20
Felt polishing disc*
21
Cup brush*
22
Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
OBJ_BUCH-1217-006.book Page 8 Thursday, February 16, 2017 9:13 AM
