D7212GV3 |
Program Entry Guide | 2.0
Panel and Area Wide Parameters
EN
| 9
Bosch Security Systems, Inc. | 10/11 | F01U170808-02
Keypad Programming of Phone #
D1255
1.
Refer to
Figure 1
on page 6 to access Keypad
Programming and navigate to the
PHONE
NUMBERS
option.
2.
At the
PHONE 1 - 4
prompt, enter the phone
number you wish to configure and press [ENT].
The current phone number shows.
If the current phone number is longer
than 20 characters, use the [PREV] and
[NEXT] keys to view the additional
characters.
3.
Press [ENT] to change the phone number.
4.
The [PREV] button acts as a [Backspace] key
and the [COMMAND] key scrolls through special
characters. Press [PREV] to delete the
characters of the phone number, and then enter
the new phone number. Press [COMMAND] to
cycle through the special dialing characters
{*, #, C, D}, then press [NEXT] to choose a
character.
5.
Press [ENT] to save the phone number.
6.
When the keypad reads
PARAMETER SAVED
,
your selection has been configured.
D1260
1.
Refer to
Figure 2
on page 7 to access Keypad
Programming and navigate to the
Phone
Numbers
option and press the corresponding
softkey.
2.
At the
Phone (1-4)
prompt, enter the phone
number you wish to configure and press
[ENTER]. The current phone number shows.
If the current phone number is longer
than 20 characters, the Previous and
Next softkeys appear. Use the softkeys to
scroll to view the additional characters.
3.
Press the
Edit
softkey to change the phone
number.
4.
Pause
(3 sec pause - "C") and
DT Detect
(Dial
Tone Detect - "D") softkeys enter special
characters. The
Backspace
softkey allows you
to erase characters. The
Clear
softkey allows
you to clear the entire phone number. The
[COMMAND] and [ENTER] keys allow you to
enter an * or a #. Use the softkeys, the number
buttons, and the [COMMAND] and [ENTER] keys
on the keypad to enter the new phone number.
5.
Press the
Save
softkey.
When the keypad reads
Parameter Saved
, your
selection has been configured.
2.2 Phone
Parameters
The program items in this category describe panel-
wide characteristics for telephone dialing, receiver
format, and supervision.
Phone # Format
Default:
Modem IIIa
2
Selection:
Modem IIIa
2
or Contact ID
Modem
IIIa
2
Modem IIIa
2
Communication
Format
Contact ID ANSI-SIA Contact ID
Central Station Receiver Format for Transmission
of Reports:
Phone # Format provides many
reporting advantages over the Contact ID format.
Refer to the
central station receiver Report Directory
(P/N: 74-04651-001) for more information about the
effect of reporting formats.
Reports identify points as 001 through 040 and
passcode User ID codes as 000 through 099 at the
central station receiver (unless
Point/User Flag
is
programmed Yes; refer to the
Point/User Flag
prompt in this section). When reporting point events,
Modem IIIa
2
Communication Format also sends point
text to the central station receiver as programmed in
Point Assignments.
Keypad Programming of Phone # Format
D1255
1.
Refer to
Figure 1
on page 6 to access Keypad
Programming and navigate to the
PHONE
PARAMETERS
option.
2.
At the
PHONE 1 - 4
prompt, enter the phone
route number you wish to configure and press
[ENT].
3.
Press [NEXT] or [PREV] to toggle between
Contact ID and ModemIII
2
and press [ENT] to
select the desired phone format.
When the keypad reads
PARAMETER SAVED
, your
selection has been configured.
D1260
1.
Refer to
Figure 2
on page 7 to access Keypad
Programming and navigate to the
Phone
Parameters
option and press the corresponding
softkey.
2.
At the
Phone (1-4)
prompt, enter the phone route
number you wish to configure and press
[ENTER]. The current configuration shows.
3.
Press the
Edit
softkey to change the phone
format.
4.
Select the softkey for the option to which you
wish to change. Press the
Save
softkey
