Bosch D4412 Operation And Installation Manual Download Page 52 | Manualshive

Page: 52 / 76

background image

D6412/D4412 Operation and Installation Guide

Page 52

© 2003 Bosch Security Systems

45349E

D6412/D4412

12.3.4

Configuration Jumpers

P2 – Diagnostic LED Pins

The diagnostic LEDs can be used for troubleshooting
purposes. See Figure 40 for jumper plug placements.

The DX4010 draws more current when the
diagnostic LEDs are enabled. Do not enable the
diagnostic LEDs under normal operating
conditions.

•

BUS RX LED:

SDI bus receives data from control panel.

•

BUS TX LED:

SDI bus transmits data to control panel.

• SER RX LED:

RS-232 receives data from printer (or other serial device connected to DX4010).

•

SER TX LED:

RS-232 transmits data to printer (or other serial device connected to DX4010).

P3 – RS-232 Cable Ground Pins

Some devices connected to the DB9 connector may cause a ground fault condition on the control panel. If this occurs,
removing the plug across the P3 jumper pins may clear the ground condition.

Some devices can cause a ground fault even if the P3 jumper plug is removed.

•

P3 Jumper Pins Disabled:

Isolate DB9 Shield from SDI Common (Black)

•

P3 Jumper Pins Enabled:

Connect DB9 Shield to SDI Common (Black)

Address DIP Switches

Use the address DIP switches to assign Address 250 to the
DX4010 when a serial device is connected to it. Set the DIP
switches to Address 0 (zero) when preforming a remote
programming direct connection. See Figure 41 for proper
DX4010 DIP Switch positioning, and Table 18 for DX4010
address settings.

DIP Switch Settings

DIP Switches

S1

S2

S3

S4

S5

S6

Module Address

1

2

4

8

16

Mode

0

ON

ON

ON

ON

ON

OFF

250

ON

ON

ON

ON

ON

ON

Table 18: DX4010 Address Settings

12.3.5

Supervision

Supervision includes operation of the SDI bus, printer paper supply, and serial printer (or device) selected (on-line). The
panel sends an SDI Missing Report if it fails to communicate with the DX4010 Module.

12.3.6

DX4010 Module’s DB9 Connector

The DB9 pins are configured as shown in Figure 42.

1 - DCD

4 - DTR

7 - RTS

2 - RxD

5 - GND

8 - CTS

3 - TxD

6 - DSR

9 - RI

Figure 42: DX4010 D89 Connector Layout

SDI Devices

Diagnostic LED Pins (P2)

Disabled

Enabled

Cable Ground Pins (P3)

Disabled

Enabled

Figure 40: DX4010 P2/P3 Jumper Pin Settings

ON

1

2

3

4

5

6

1

2

4

8

16

M
O
D
E

OFF

ON

Address 0 (zero) Settings

Figure 41: DX4010 DIP Switch Orientation

1

2

3

4

5

6

7

8

9

«
...
50
51
52
53
54
...
»

Summary of Contents for D4412













































































Reviews:

No comments

Related manuals for D4412

Brand: KAR-TECH Pages: 28

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: Eaton Pages: 28

Brand: Parallel Pages: 16

Brand: V2 Pages: 46

Brand: Lawler Pages: 5

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 2

phyCORE-MCF548x

Brand: Phytec Pages: 104

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Brand: WEST Pages: 2

Brand: Zencontrol Pages: 2

Brand: Daikin Pages: 2

Brand: Advantech Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands