Bosch D4412 Operation And Installation Manual Download Page 20 | Manualshive

Page: 20 / 76

background image

D6412/D4412 Operation and Installation Guide

Page 20

© 2003 Bosch Security Systems

45349E

D6412/D4412

Power Supply

CAUTION

Investigate low battery reports immediately: If primary (AC) power is off and the discharge continues, the panel
becomes inoperative when the battery voltage drops below 10.2 VDC.

4.2.5

Battery Charging Circuit - Float Charge

The float voltage for the battery charging circuit is 13.5 VDC to 13.9 VDC at a maximum current of 1.4 A.

4.2.6

Battery Discharge/Recharge Schedule

Discharge Cycle

• AC Off: Command centers indicate trouble. AC Fail Report sent as programmed.

• 13.8 VDC

:

Charging float level

• 12.1 VDC: Low battery trouble at command centers. Low Battery Report as programmed.

• 10.2 VDC: Panel shuts down as voltage falls below 10.2 VDC

Recharge Cycle

• AC On: Panel restarts, battery charging begins, AC Restoral Report sent as programmed, AC trouble clears from

command centers.

• 13.0 VDC: Battery restoral reports sent, battery trouble clears from command centers

• 13.8 VDC: Battery float charged.

4.2.7

System Status LED

The System Status LED shows system status, including power supply status as described in Table 4. See Figure 4 for the
location of the LED on the panel.

System Status

LED Display

System Normal

On for 50 ms; Off for 1 sec.

Battery Missing

Off for 200 ms; On for 1 sec.

AC Missing

Off for 200 ms; On for 200 ms
Off for 200 ms; On for 1 sec.

Phone Ringing

Flickers for 1 sec. as each ring is detected.

Phone Line Seized (panel using phone line)

On solid.

Shut Down (system voltage below 10.2 VDC)

Off for 200 ms; On for 200 ms
Off for 200 ms; On for 200 ms
Off for 200 ms; On for 1 sec.

Table 4: System Status LED Description

4.3

External Power Supply

The external power supply (not supplied) is not intended to provide power to
indicating devices for burglary and fire applications.

•

Burglary Applications

use a UL603 Listed burglar alarm power supply

with an operating voltage range of
11.8 VDC to 12.4 VDC for Bank Safe/Vault applications (72 hrs. of
standby battery required).

•

Fire Applications

use a UL1481 Listed power supply operating voltage

range of 11.8 VDC to 12.4 VDC for fire applications.

L-2

Com

L-3

System Status LED

Figure 4: System Status LED

«
...
18
19
20
21
22
...
»

Summary of Contents for D4412













































































Reviews:

No comments

Related manuals for D4412

ACS850-04 series

Brand: ABB Pages: 296

Brand: ABB Pages: 320

Brand: ABB Pages: 50

Brand: ABB Pages: 56

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: Daikin Pages: 5

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: eclisse Pages: 40

Brand: LAS Pages: 6

Brand: MAKOT Pages: 6

Brand: QUNDIS Pages: 2

Brand: Vag Pages: 12

Brand: Matelec Pages: 16

Brand: HQ Power Pages: 23

Brand: Woodward Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands