Bosch Compress 3000 DW FO HP 270-1E 0 FOV/S Installation Instructions Manual Download Page 40

Page: 40 / 48

6 720 801 244 (2013/08)

Compress 3000 DW FO

40 | Display

Display

7.1

Fault display

Installation, maintenance and repairs may only be carried out by an authorised contractor. The following table lists the fault codes
and their remedies.

Display

Description

Solution

E01

Fault in the top storage tank temperature sensor

Notify authorised contractor

E02

Fault in the bottom storage tank temperature sensor

Notify authorised contractor

E03

Fault in the temperature sensor at the air inlet

Notify authorised contractor

E05

Not used

Notify authorised contractor

E06

Hold down setting keys longer than 30 seconds

Release keys

E07

Not used

Notify authorised contractor

E08

Not used

Notify authorised contractor

E09

Incorrect system purging

Water shortage during off-peak

Water shortage for long period (> 12h)

Notify authorised contractor

Reset the system

E10

Heating element faulty

Fault in the high limit safety cut-out

Adjusted temperature in the thermostat below the set

point temperature in the tank

Notify authorised contractor

E11

Fault in the fan

High pressure loss in the air ducts

Leak in refrigerant circuit

Fault in the compressor

Fault in the expansion valve

Fault in the dry filter

Start up after a long standby period at very low

temperatures

Reset the system and notify authorised contractor

Table 6

Fault codes

Summary of Contents for Compress 3000 DW FO HP 270-1E 0 FOV/S

















































Search results

Summary of Contents for Compress 3000 DW FO HP 270-1E 0 FOV/S

Reviews:

Brands by name

Popular brands

Bosch Compress 3000 DW FO HP 270-1E 0 FOV/S, Installation Instructions Manual

Search results

Summary of Contents for Compress 3000 DW FO HP 270-1E 0 FOV/S

Reviews:

Brands by name

Popular brands