manualshive.com logo in svg

Bosch Compress 3000 DW FO HP 270-1E 0 FOV/S, Installation Instructions Manual

Share
Download
Bosch Compress 3000 DW FO HP 270-1E 0 FOV/S Installation Instructions Manual Download Page 38

6 720 801 244 (2013/08)

Compress 3000 DW FO

38 | Maintenance and repair

Fig. 49

Temperature in the bottom part of the storage tank

"3d" function

The "3d" function can be used to check the ambient air 
temperature.

Fig. 50

Ambient air temperature

"5d" function

The "5d" function can be used to check the current power 
consumption of the appliance.

Fig. 51

Power consumption of the appliance

"6d" function

The "6d" function can be used to check the number of air 
defrost cycles.

Fig. 52

Number of air defrost cycles

Functions "1F" to "10F"

The functions "1F" to "10F" can be used to display the last 10 
faults that occurred.

•

"1F"  -  last  fault

•

"2F" - second to last fault

•

.....

•

"10F" - tenth to last fault

Fig. 53

Last fault

6720646160-02.1V

6720646160-03.1V

6720646160-04.1V

6720801244-21.1V

6720646160-31.1V

Summary of Contents for Compress 3000 DW FO HP 270-1E 0 FOV/S

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands